Start-Up; General Information; Preparation; Start-Up Procedure - Dimplex LIK 8TES Instructions D'installation Et D'utilisation

LIK 8TES
8

Start-UP

8.1 General Information

To ensure that start-up is performed correctly, it should only be
carried out by an after-sales service technician authorised by
the manufacturer. These measures can also include an addi-
tional warranty under certain conditions (see Warranty).

8.2 Preparation

The following items need to be checked prior to start-up:
All of the heat pump connections must be established as

described in Chapter 6.
All valves that could impair the proper flow of the heating

water in the heating circuit must be open.
 The air intake and air outlet paths must be clear.
The ventilator must turn in the direction indicated by the

arrow.
 The heat pump manager must be adapted to the heating
system in accordance with the controller's operating in-
structions.
Ensure the condensate outflow functions.

The outflow from the heating water pressure relief valve

must also function correctly.
De-aeration of the heating system:

Ensure that all heating circuits are open and the heat circu-
lating pump is operating (level III).
Connect the voltage to the heat pump manager. Select the
heat generator 2 operating mode and de-aerate the sys-
tem at its highest point. Top up with water if required
(maintain static minimum pressure).

8.3 Start-Up Procedure

The heat pump is started up via the heat pump manager. Ad-
justments should be made in compliance with the instructions.
The overflow valve must be adjusted to the requirements of the
respective heating system. Incorrect adjustment can lead to
faulty operation and increased energy consumption. We rec-
ommend carrying out the following procedure to correctly ad-
just the overflow valve:
Close all of the heating circuits that may also be closed during
operation (depending on the type of heat pump usage) so that
the most unfavorable operating state - with respect to the
water flow rate - is achieved. This normally means the heating
circuits of the rooms on the south and west sides of the build-
ing. At least one heating circuit must remain open (e.g. bath-
room).
The overflow valve should be opened far enough to produce
the maximum temperature spread between the heating flow
and return flow listed in the following table for the current heat
source temperature. The temperature spread should be meas-
ured as close as possible to the heat pump. The heating ele-
ment of mono energy systems should be disconnected during
start up.
www.glendimplex.de
Heat source
temperature
From
-20 °C
-14 °C
-9 °C
-4 °C
1 °C
6 °C
11 °C
16 °C
21 °C
26 °C
31 °C
At hot water temperatures under 7 °C, start-up is not possible.
The water in the buffer tank must be heated to a minimum of
18 °C with the second heat generator.
To ensure a problem-free start-up, the following procedure is to
be implemented:
1) Close all consumer circuits.
2) Ensure that the heat pump has the correct water flow.
3) Use the manager to select the automatic operating mode.
4) In the special functions menu, start the "Start-up" program.
5) Wait until a return temperature of at least 25 °C has been
reached.
6) Now slowly reopen the heating circuit valves in succession
so that the heating water flow is constantly raised by
slightly opening the respective heating circuit. The heating
water temperature in the buffer tank must not be allowed
to drop below 20 °C during this process. This ensures that
the heat pump can be defrosted at any time.
7) When all heat circuits are fully open and a return tempera-
ture of at least 18 °C is maintained, the heat pump start-up
is complete.
CAUTION!
Operating the heat pump at low system temperatures may
cause the heat pump to break down completely. After a
prolonged power failure, the commissioning procedure
detailed above must be followed.
452161.66.20a · FD 0106
Max. temperature spread
between heating flow and return
flow
To
-15 °C 4 K
-10 °C 5 K
-5 °C 6 K
0 °C 7 K
5 °C 8 K
10 °C 9 K
15 °C 10 K
20 °C 11 K
25 °C 12 K
30 °C 13 K
35 °C 14 K
English
EN-11