BFT ARES BT A 1000 Mode D'emploi page 13

TABLE "B" - LOGICS
Any modification of parameters/logics must be confirmed by pressing S2 > 5s
DIP Logic
Transmitter
1
programming
2 BAR / 8K2
Photocell input
3
check
4 Edge input check
Photocells
5
during closing
6 Fast closing
Block pulses
7
during opening
8 3-step logic
Safety edge input
6
operation
7 Fast closing
Residential /
apartment
8
building
operation
INSTALLATION MANUAL
Cross out
Default Description
setting used
Enables wireless memorizing of transmitters:
1- Press in sequence the hidden key and normal key (T1-T2-T3-T4) of a transmitter that has already
been memorized in standard mode via the radio menu.
2- Press within 10 sec. the hidden key and normal key (T1-T2-T3-T4) of a transmitter to be memorized.
ON
The receiver exits programming mode after 10 sec.: you can use this time to enter other new
transmitters.
ON
This mode does not require access to the control panel.
IMPORTANT: Enables the automatic addition of new transmitters, clones and replays.
Disables wireless memorizing of transmitters and automatic addition of clones.
OFF Transmitters are memorized only using the relevant Radio menu or automatically with replays.
IMPORTANT: Disables the automatic addition of new transmitters and clones
Input configured as Bar 8k2. Input for resistive edge 8K2.
ON
The command reverses movement for 2 sec.
OFF
Input configured as Bar, safety edge.
OFF
The command reverses movement for 2 sec.
ON Enable safety check on the PHOT input
OFF
OFF Safety check on PHOT input not enabled
ON Enable safety check on the BAR input
OFF
OFF Safety check on BAR input not enabled
In the event beam is broken, photocell operation is disabled during opening. During closing,
ON
movement is reversed immediately.
OFF
When beam is broken, photocells are active during both opening and clo-
OFF sing. When beam is broken during closing, movement is reversed only once the
photocell is cleared.
ON Closes 3 seconds after the photocells are cleared before waiting for the set TCA to elapse.
OFF
OFF Logic not enabled
ON The start pulse has no effect during opening.
OFF
OFF The start pulse has effect during opening.
Switches to 3-step logic; during closing, start
ON
reverses movement.
OFF
OFF Switches to 4-step logic.
ON Safety edge with active reversal only when closing, when opening the movement stops
OFF
OFF Safety edge with active reversal in both directions
ON Closes 3 seconds after the photocells are cleared before waiting for the set TCA to elapse.
OFF
OFF Logic not enabled
Sets the automation type of operation:
ON
ON = Apartment building
OFF OFF = Residential
Reaction to the START input (wired or radio):
CLOSED
WHILE CLOSING
OPEN
WHILE OPENING
AFTER STOP
Reaction to the OPEN input (wired):
OFF
CLOSED
WHILE CLOSING
OPEN
WHILE OPENING
AFTER STOP
Reaction to the PEDESTRIAN input (radio):
CLOSED
WHILE CLOSING
OPEN
WHILE OPENING
AFTER STOP
Only active on FW < 3.03
Only active on FW ≥ 3.03
Residential
Opens
Stops
Closes
STOPS + TCA
Opens
Residential
Opens
Opens
No effect
Keeps it open
Opens
Residential
Opens partially
Stops
Closes
STOPS + TCA
Opens partially
CLOSED
DURING CLOSING
OPEN
DURING OPENING
AFTER STOP
Apartment building
Opens
Opens
Closes
No effect
Opens
Apartment building
Opens
Opens
No effect
Keeps it open
Opens
Apartment building
Opens partially
Opens partially
Closes
No effect
Opens partially
ARES BT A 1000-1500 -
3 step 4 step
opens
opens
stop
closes closes
stop + stop +
TCA TCA
opens opens
13