GRAUPNER ULTRAMAT 18 Instructions D'utilisation page 41

Input voltage and Battery resistance display
INC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
I n p u t V o l t a g e
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 3 . 6 2 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Battery Res.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 5 . 3 m
The battery resistance is one important value to determine the battery quality. Press any button
to return to the menu system. Internal resistance is displayed every 1 minute for 10 minutes
after charge starts (NiCd, NiMH) Internal resistance is displayed one time after 2 minutes after
discharges starts (NiCd, NiMH, LiIo, LiPo, LiFe).
Internal resistance is displayed every 1 minute after charge starts (LiIo, LiPo, LiFe). Internal
resistance on individual cell is displayed with the connected balancer cable (LiIo, LiPo, LiFe
cells). Internal resistance is not displayed in storage mode or if the charge voltage reaches CV
during operation. The cell voltage gap against cell average value is showing as bar.
INC DEC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
I n p u t V o l t a g e
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 3 . 6 2 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Battery Res.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 5.3 m
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 . 4 . 1 5 3 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 . 4 . 1 6 8 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
3 . 4 . 0 5 3 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
4 . 0 . 0 0 0 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
5 . 0 . 0 0 0 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
6 . 0 . 0 0 0 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
7 : 4 . 1 3 3 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
8 : 4 . 1 2 8 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
9 : 4 . 0 1 3 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 0: 0 . 0 0 0 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 1: 0 . 0 0 0 V
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 2: 0 . 0 0 0 V
The current input voltage and battery resistance can be
DEC
called up at any time by pressing the INC and DEC
buttons simultaneously.
Change the display with INC or DEC button to input
voltage, the battery resistance display and to the single
cell voltages and backwards.
Displaying the Input voltage can be very useful if you are
using your car's battery as energy source for charging.
Display the voltage of the single cells
The current input voltage and battery resistance can be
called up at any time by pressing the INC and DEC
buttons simultaneously.
Change the display with INC or DEC button to input
voltage, the battery resistance display and to the single
cell voltages and backwards.
Displaying the single cell voltages is useful to check the
single cell voltages.
Displaying the single cell resistance is useful to check the
single cell quality.
1 : 4 . 4 2:
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
3 : 5 . 0 4:
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
5 : 0 . 0 6:
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
7 : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 . 2 8:
9 : 4 . 6 10: 4 . 8 m
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 1: 0 . 0 12: 0 . 0 m
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
4 . 5 m
0 . 0 m
0 . 0 m
4 . 4 m
41