Starting The Charge / Discharge Process - GRAUPNER ULTRAMAT 18 Instructions D'utilisation

10. Starting the charge / discharge process

3 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L i P o m a n u a l
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C : 2 . 5 A 2 0 0 0 m A h
2
START
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R C O N .
2
START
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A T T E R Y C H E C K
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T P L E A S E . . .
2
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C H G 2 3 : 4 0
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L P + 2 . 5 0 A
30
For charging / discharging, or conditioning a pack, select
the desired program as described below, and then set
suitable values.
If the battery does have a balancer connector, connect the
balancer connector to the balancer input (BALANCER
CONNECTOR) of the charger.
Make sure for the right polarity.
From right handed to left side:
Pin1/1 (GND): Ground = battery1 -,
Pin1/2 (1): + cell 1, Pin1/3 (2): + cell 2, Pin1/4 (3): + cell 3,
Pin1/5 (4): + cell 4, Pin1/6 (5): + cell 5, Pin1/7 (6): + cell 6
Pin2/1 (GND): Ground = battery 2 -,
Pin2/2 (1): + cell 7, Pin2/3 (2): + cell 8, Pin2/4 (3): + cell 9,
Pin2/5 (4): + cell 10, Pin2/6 (5): + cell 11, Pin2/7 (6): + cell 12
Connect the two pole power charging cable of the battery to
the charger output - BATTERY + with the right polarity.
Hold the START button pressed in for about two seconds,
and the charger display, if the balancer connector is
connected or not. With connected balancer connector the
single cell voltages can be displayed, see 16..
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A T T E R Y
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * * L i P o
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
3
+
START
Press the START button again,
and the charger will assess the
battery.
You can interrupt the charge process at any time with another
0 0 8 6 3
short press on the START button.
Note: if you interrupt the charge process by pressing
1 4 . 0 1 V
the START button, all display parameters are
irretrievably erased.
N O T
2
sec.
C H E C K
P L E A S E . . .
If a Li-battery is connected, the charger
will display the cell count of the Lithium
2
pack, which must be corrected manually
sec.
with the INC or DEC buttons, if it is wrong.
c e l l s * * *
c e l l s ( 1 3 . 7 3 V )
-
INC
DEC
C O N
! Caution ! Please
take great care to set
the correct cell
count. and the right
battery type. If you
make a mistake, the
battery could
explode and burst
into flames !