General Safety Rules; Work Area Safety; Electrical Safety; Personal Safety - Ryobi RPT400 Manuel D'utilisation

GB
F D E I P

GENERAL SAFETY RULES

WARNING
Read and understand all instructions. Failure to
follow the warnings and instructions may result in
electric shock, fire and serious injury.
The term "power tool" in the warnings refer to
your mains-operated corded power tool.

WORK AREA SAFETY

n
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
n
Do not operate power tools in explosive atmospheres,
such as in the presence of fl ammable liquids, gases or
dust. Power tools create sparks which may ignite the
dust or fumes.
n
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.

ELECTRICAL SAFETY

n
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodifi ed plugs and
matching outlets will reduce risk of electric shock.
n
Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is
earthed or grounded.
n
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
n
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
n
When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
n
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply, the tripping current of 30mA or
less.

PERSONAL SAFETY

n
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the infl uence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal
NL S DK N FIN GR HU
English
n
n
n
n
n
n
POWER TOOL USE AND CARE
n
n
n
n
n
n
9
CZ RU RO PL SLO HR TR EST LT
injury.
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
with your fi nger on the switch or plugging in power
tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventative safety measures
reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tool's operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
LV SK BG