Additional Safety Instructions - Scheppach SD1600V Traduction Des Instructions D'origine

11. Do not use the cable for purposes for which it
is not intended
- Do not use the cable to pull the plug out of the sock-
et. Protect the cable from heat, oil and sharp edges.
12. Secure the workpiece
- Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held more
securely than with your hand.
13. Avoid abnormal working postures
- Make sure you stand squarely and keep your bal-
ance at all times.
14. Take care of your tools
- Keep cutting tools sharp and clean in order to be
able to work better and more safely.
- Follow the instructions for lubrication and for tool
replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check theextension cable regularly and replace
it if damaged.
- Keep handles dry and free from oil and grease.
15. Pull the connector out of the socket
- When the electric tool is not in use or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
16. Always remove keys and wrenches after use
- Always check that keys, wrenches and other
adjusting tools have been removed before you
switch on the equipment.
17. Avoid unintentional starting
- Make sure that the switch is turned off when con-
necting the tool to the power supply.
18. Use extension cables for outdoors
- Check that it is approved for outdoor duty and is
marked accordingly.
19. Be alert at all times
- Watch what you are doing. Use common sense
when working. Never use the tool when you are
distracted.
20. Check the electric tool for potential damage
- Protective devices or other parts with minor dam-
age must be carefully inspected to ensure that
they function correctly and as intended prior to
continued use of the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-free
operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
specialist workshop, insofar as nothing different
is specified in the user manual.
- Damaged switches have to be replaced by a cus-
tomer service workshop.
- Do not use any electric tool on which the switch
cannot be switched on and off.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
21. ATTENTION
- The use of other insertion tools and other acces-
sories can entail a danger of injury.
22. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
WARNING
This electric tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.

5.2 Additional safety instructions

• Switch the machine off immediately and pull the
power plug in an emergency.
• Follow all these safety instructions before and while
working with the saw.
• Never use the saw to cut firewood.
• The machine is equipped with a safety switch
against reactivation if the voltage drops.
• If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
saw's power consumption. Minimum cross-section
1,5 mm 2 .
• If you use a cable reel, the complete cable must be
pulled off the reel.
• Persons working on the machine should not be dis-
tracted.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
• Only fit blades which are well sharpened and have
no cracks or deformations.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the
data specified in this manual.
• It is imperative to make sure that all devices which
cover the saw blade are in good working order.
• Never dismantle the machine's safety devices or
render them inoperative.
• Damaged or faulty safety devices have to be re-
placed immediately.
• Never cut workpieces which are too small to hold
securely in your hand.
• Never load the machine so much that it cuts out.
• Always press the workpiece firmly against the saw
table.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
GB | 23