Black & Decker ADV1210 Traduction Des Instructions D'origine page 6

Warning! The cigarette lighter connector is fi tted
with a non-serviceable safety fuse. The fuse may
operate in the event of a fault. If this occurs the
fuse must be replaced together with the connector
and cable by the manufacturer or an authorised
Black and Decker Service Centre in order to avoid
a hazard.
Warning! Do not operate the appliance with
systems which have positive ground or a different
voltage.
Symbols on the appliance
Read all of this manual carefully before
using the appliance.
Features
This tool includes some or all of the following
features.
1. On/off switch
2. Bowl release button
3. Dust bowl
4. Nozzle (ADV1220 only)
5. 12V car connector
Fig. A (ADV1210 only)
6. Brush head
7. Crevice tool
Fig. B (ADV1220 only)
8. Large brush head
9. Large crevice tool
10. Flexible hose
Assembly
Accessories (fi g. A & B)
These models may be supplied with some of the
following accessories:
♦
Brush head (6) (ADV1210 only).
♦
Crevice tool (7) (ADV1210 only).
♦
Large brush head (8) (ADV1220 only).
♦
Large crevice tool (9) (ADV1220 only).
♦
Flexible hose (10) (ADV1220 only).
Fitting the accessories (Fig. A) (ADV1210 only)
♦
Insert the appropriate accessory into the
front of the appliance. Make sure that the
accessory is pushed fully in.
Fitting the accessories (Fig. B) (ADV1220 only)
♦
Fit the appropriate accessory on to the short
end of the fl exible hose (10). Make sure that
the accessory is pushed fully on.
♦
Fit the long end of the fl exible hose (10) into
the front of the appliance. Make sure that the
fl exible hose is pushed fully in.
Use
Connecting to the vehicle's power supply
♦
Make sure that the appliance is switched off.
♦
Remove the cigarette lighter from it's socket.
♦
Plug the 12V car connector (5) into the
cigarette lighter socket.
Switching on and off (fi g. C)
♦
To switch the appliance on, slide the on/off
switch (1) forward to position 1.
♦
To switch the appliance off, slide the on/off
switch (1) back to position 0.
Optimising the suction force
In order to keep the suction force optimised, the
fi lters must be cleared regularly during use.
Emptying and cleaning the product.
Quick empty the dust bowl (fi g. D)
(ADV1220 only)
♦
Press the release latches (11) and pull the
nozzle (4) straight off.
♦
Empty the contents of the bowl.
♦
To replace the nozzle, place it back onto the
handle until it "clicks" fi rmly into position.
Removing the dust bowl and fi lters (fi g. E)
Warning! The fi lters are re-usable and should be
cleaned regularly.
♦
Press the release latch (2) and pull the dust
bowl (3) straight off.
♦
While holding the dust bowl over a bin, pull out
the fi lter to empty the contents of the bowl.
♦
To replace the dust bowl, place it back onto
the handle until it "clicks" fi rmly into position.
Warning! Never use the appliance without
the fi lters. Optimum dust collection will only be
achieved with clean fi lters.
Pre-fi lter (fi g. F) (ADV1220 only)
The Filter and pre-fi lter can be separated to allow
better cleaning.
♦
Twist the pre-fi lter (12) in a clockwise direction
and lift from the fi lter (13).
Cleaning the dust bowls and fi lters
♦
The dust bowls and fi lters can be washed in
warm soapy water.
♦
Make sure that the fi lters and the dust bowl
are dry before re-fi tting.
Replacing the fi lters
The fi lters should be replaced every 6 to 9 months
and whenever worn or damaged.
ENGLISH
5