Johnson Outdoors TALON 1810302 Mode D'emploi page 7

2
ITEM(S) NEEDED
#20 x 1
d. Take the Flag Mounting Plate Bracket (Item #8) and
slide it into the short C-channel segment of the Arm
Bracket. Assemble the Bolts to lock it into position.
Use two ½"-13 X 4 ¼" Stainless Steel Bolts (Item
#22), four ½" Heavy Duty Stainless Steel Washers
(Item #24) and two ½"-13 Nylock Nuts (Item #26).
Apply anti-sieze (Item #20). Each Bolt should have
a washer placed before sliding into the Arm Bracket
and Flag Plate.
NOTICE:
When properly installed, the Mounting
Plate should be nearly parallel to the Transom of
the boat. It should also be oriented as close to the
Transom as possible to minimize the possibility of
water spray.
e. Tighten all hardware to 50 ft-lbs.
3
ITEM(S) NEEDED
#12 x 4
NOTICE:
To prevent seizing of the stainless steel
hardware, do not use high speed installation tools.
Applying an anti-seize may help prevent seizing.
f. The Talon Mounting Bracket should be secured
to the Flag Mounting Plate Bracket. Remove any
hardware that may have previously been used
to secure the Mounting Bracket to the Transom.
Keep the Bolts and Mounting Straps on the Talon
Mounting Bracket in place.
g. Take four of the 5/15-18 X 2" Stainless Steel Bolts
(Item #12) and four of the 5/16 Flat Washers (Item
#14) and place one washer on each bolt. Align
the mounting holes on the Talon Bracket with the
mounting holes on the Flag Mounting Plate Bracket.
Place one bolt in each of the corner mounting holes.
h. Secure the Brackets together by taking the four of
.750 x .3125 Stainless Steel Washers (Item #16)
and place them on the end of the bolts. Place
anti-sieze (Item #20) on the hardware and secure
each with the four 5/16-18 Nylock Nut (Item #18).
Tighten the bolts with a 1/2" Box End or Socket
Wrench. Do not over-tighten.
7 | minnkotamotors.com
#22 x 2 #24 x 4
#14 x 4 #16 x 4
#26x 2
2d
Flag Mounting Flag Mounting
Plate Bracket Plate Bracket
Column Column
C-channel C-channel
Arm Arm
Bracket Bracket
#18 x 4 #20 x 1
3g
Stainless Steel Stainless Steel
Washer Washer
Elbow Elbow
Bracket Bracket
Bracket Bracket
NOTICE:
Be sure to position the heavy duty .750 x
.3125 Washers over the slots on the inboard side of the
Flag Mounting Plate Bracket.
NOTICE:
Consider mounting a Talon Tilt Bracket
#1810222 for additional adjustability. To learn more visit
minnkotamotors.com.
#8 x 1
2e
Nylock Nut Nylock Nut
Flag Mounting Flag Mounting
Heavy Duty Heavy Duty
Stainless Stainless
Steel Steel
Washer Washer
Arm Arm
Bracket Bracket
Heavy Duty Heavy Duty
Stainless Steel Stainless Steel
Washer Washer
Nylock Nut Nylock Nut
Arm Arm
Talon Mounting Talon Mounting
Bracket Bracket
Stainless Stainless
Steel Bolt Steel Bolt
©2019 Johnson Outdoors Marine Electronics, Inc.
Plate Bracket Plate Bracket
Stainless Stainless
Steel Bolt Steel Bolt
Flag Flag
Mounting Mounting
Plate Plate
Bracket Bracket
Flat Flat
Washer Washer