Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Do not touch the blade before the safety key has
been removed and the blades have come to a complete stop.
Release the bail bar (2) to turn mower off, wait for the
blade to stop and remove the safety key (1).
Cut a piece of wood (approximately 50 mm x 100 mm x
600 mm long) to use to keep the blade from turning while
Turn the mower on its side.
Wear gloves and proper eye protection. Be careful
of the sharp edges of the blade.
Remove the washer (30), blade (31), square blade guide
and fan (33) for damage and replace if necessary.
blade (Indicated by arrows on either end) will face the ground
when the mower is returned to its normal upright position.
Install the fan (33). Be sure to position the fan blades (34)
so that they face in towards the mower.
Install the blade guide (32). Be sure to position the 'D'
shaped pegs (35) so that they face out, away from the
mower.
Fit the blade (31) onto the blade guide (32) with the ar-
rows facing outwards.
Position the piece of wood (28) to keep the blade (31)
with a 13mm wrench.
Keep the blade sharp for best performance. A dull blade does
not cut grass cleanly or mulch properly.
Always make sure that the safety key is removed.
Wear proper eye protection while removing, sharp-
ening and installing a blade.
Sharpening the blade twice during a mowing season is usually
blade to dull quickly. If your lawn has sandy soil more frequent
sharpening may be required.
Replace bent or damaged blades immediately.
(Original instructions)
Make sure that the blade remains balanced.
Sharpen the blade at the original cutting angle.
Sharpen the cutting edges on both ends of the blade,
removing equal amounts of material from both ends.
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1) and the battery pack (22) and
turn the lawnmower on to its side.
Remove the blade (31) from the mower, see the instruc-
tions for removing and installing blades.
Wear proper eye protection and gloves and be
careful of the sharp edges of the blade.
Put the blade (31) in a vice.
cutting edge.
Check the balance of the blade, see the instructions for
blade balancing.
Install the blade (31) on the mower and tighten securely,
see the instructions for removing and installing blades.
Check the balance of the blade by putting the centre hole
in the blade on to a nail or a round shank screwdriver that
is clamped horizontally in a vice. If either end of the blade
is balanced.
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1).
Use only mild soap and a damp cloth to clean the mower.
Use a blunt tool to clean out any clippings which may have
accumulated on the underside of the mower.
After several uses, check all exposed fasteners for tight-
ness.
Fertilisers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilisers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1).
Wipe all exposed parts with a damp cloth.
Publicité
Table des Matières
