User Manual; Ignition; Controlling The Temperature; Switching Off - Dru OPÉRA DVS 2-01 Instructions D'installation Et Mode D'emploi

Ignition button A has three positions, i.e.:
O position

USER MANUAL

Pilot burner position
Full position
Turn the ignition button to the left from position O,
USER MANUAL
press down firmly as well and keep turning to the
pilot burner position . By turning the button, the

Ignition

pilot burner is ignited by means of an electrical
Ignition button A has three positions, i.e.:
spark. When the pilot burner burns, keep pressing
down the button for approx. 10 sec. and then let
O position
go. The pilot burner is visible from the side, behind
Pilot burner position
the glass window. If the pilot burner does not
Full position
ignite at once, the above-mentioned action can be
repeated immediately by turning the pressed down
Turn the ignition button to the left from position O, press
button back towards O and then left again towards
down firmly as well and keep turning to the pilot burner
the pilot burner position. After letting go of the
position . By turning the button, the pilot burner is igni-
ignition button, the pilot burner should continue to
ted by means of an electrical spark. When the pilot burner
burn. Then turn the ignition button further
burns, keep pressing down the button for approx. 10 sec.
towards the full position . Depending on
and then let go. The pilot burner is visible from the side,
thermostat button B, the main burner will be
behind the glass window. If the pilot burner does not igni-
te at once, the above-mentioned action can be repeated ignited.
immediately by turning the pressed down button back
towards O and then left again towards the pilot burner

Controlling the temperature

position. After letting go of the ignition button, the pilot
The position of thermostat button B determines
burner should continue to burn. Then turn the ignition
the temperature in the room. Position 6 provides
button further towards the full position . Depending on
the highest temperature, position 1 the lowest.
thermostat button B, the main burner will be ignited.
The thermostat controls the burner by modulating
between "full position" and "low position" of the
Controlling the temperature
burner. The thermostat will automatically keep the
The position of thermostat button B determines the
room at the required set temperature.
temperature in the room. Position 6 provides the highest
temperature, position 1 the lowest. The thermostat

Switching off

controls the burner by modulating between "full position"
Turn ignition button A back to the Pilot Burner
and "low position" of the burner. The thermostat will
position ( symbol), only the pilot burner will
automatically keep the room at the required set
continue to burn. In order to switch off the
temperature.
appliance fully, you must press down button A and
turn it back to position O.
Switching off
Turn ignition button A back to the Pilot Burner position

Important

( symbol), only the pilot burner will continue to burn.
An incorporated safety lock will be activated if the
In order to switch off the appliance fully, you must press
appliance is set to the ,,OFF" (O) position.
down button A and turn it back to position O.
Therefore, wait 5 minutes before re-igniting the
appliance. Do not try to press down the ignition
Important
button during this time, as it is locked by means of
An incorporated safety lock will be activated if the applian-
the safety lock. Do not force the button, because
ce is set to the ,,OFF" (O) position. Therefore, wait
the mechanism could get damaged.
5 minutes before re-igniting the appliance. Do not try
to press down the ignition button during this time, as it is
locked by means of the safety lock. Do not force the

Eco control pack

button, because the mechanism could get damaged.
It is possible to order a separately available "Eco
control pack" with remote control. The "Eco
Eco control pack
It is possible to order a separately available "Eco control
pack" with remote control. The "Eco control pack" is
needed to get the best out of your appliance.
This set has a receiver that must be placed in the tray
specifically intended for this purpose.
button points to O
button points to
button points to
button points to O
button points to
button points to
This set has a receiver that must be placed in the
tray specifically intended for this purpose.
Art 2-01: The tray is located on the left side of the
gas control.
Art 3-01, 4-01, 5-01, 6-01, 8-02, 10-02: The tray is
The tray is located under the gas control and can be rea-
located under the gas control.
ched by removing the cover.
Prevent cables from making contact with hot
Prevent cables from making contact with hot internal
internal components.
components.
12
B
A
38P-0744/0