Foppapedretti Lift Mode D'emploi page 15

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19
• ENGLISH •
All manuals and user guides at all-guides.com
USE
OPENING
(fig. 1-7)
Grasp the booster chair as shown and lift up the top part; you will hear a click when it is opened correctly (fig. 3).
Lift the front part upwards (fig. 4); you will hear a click when it is opened correctly (fig. 5).
Press the buttons on the underside of the seat, as shown in the figure (fig. 6) and lower the seat to the horizontal
position while keeping the buttons pressed down. Release the buttons and make sure the seat is properly
locked (fig. 7).
ASSEMBLING THE PADDING
(fig.8-13)
Place the padding on the seat.
Completely insert the end with the stitched turn-up (a) of the strap through the corresponding slot in the seat
shell (fig. 9). If necessary, use a flat-head tool. Rotate the end of the strap which is protruding from the slot in
the shell (fig. 10).
Completely insert the end with the stitched turn-up (b) of the crotch safety strap through the fabric slot and the
corresponding slot in the seat shell (fig. 11). If necessary, use a flat-head tool. Rotate the end of the strap which
is protruding from the slot in the shell (fig. 12).
Make sure that it is correctly assembled and locked. When pulling the safety strap from the inside of the seat,
it should not slip through the slot.
Attach the press studs on the back side of the backrest.
Lift up the padded backrest by attaching it with the velcro on the back side (fig. 13).
SEAT HEIGHT ADJUSTMENT
(fig. 14)
ATTENTION: The height cannot be adjusted when the child is sitting in the booster chair.
Simultaneously press the two height adjustment buttons (a) located on the legs under the seat and select the
desired height. Release the buttons and make sure that the seat is correctly locked in the new position on both
sides. The seat can be adjusted to 3 different heights.
TRAY ASSEMBLY AND ADJUSTMENT
(fig. 15-17)
Hold down the lever on the underneath of the tray (fig. 15) and place the tray on the seat, checking that the
armrests are inside the guides located on the bottom of the tray itself (fig. 16).
Release the lever and push the tray towards the inside of the booster chair until it locks in place. A click will
indicate that it has locked correctly (fig. 17).
To adjust the tray, press the lever and pull or push the tray towards the inside of the booster chair until it is
locked in the new position (fig. 15). A click will indicate that it has locked in position correctly.
IMPORTANT: Check before use that the tray is correctly locked in the chosen position by pulling it outwards
without pressing the lever; the tray should stay in place.
IMPORTANT: The booster chair can be used without a tray, but always with the side armrests in the raised
position. The side armrests fold up to allow the product to be closed.
SAFETY HARNESS
(fig. 18-22)
CAUTION: Using a safety harness with leg separator is essential to ensure your child's safety.
CAUTION: The tray alone being attached to the seat does not guarantee that your child is secured. Always use
the safety harness!
The booster chair is equipped with a 3-point safety strap.
• Unclipping the buckle: Press the button (a) and pull out the components (b).
• Clip the buckle: Insert the components (b) into the buckle (a); you will hear a click when they are attached
correctly. Adjust the harness depending on the size of the child, using the adjusters (c) (fig. 22).
Unclip the buckle and place the child on the booster chair. It is easier to do this when the tray is removed.
15

Publicité

Table des Matières
loading

Table des Matières