Black & Decker BEMWH551 Mode D'emploi page 12

ENGLISH
Warning! Do not set the cutting height too low, especially at
the beginning of the mowing season. Cutting the grass too low
will discourage its growth and allow weed proliferation. You
will achieve a far better lawn by cutting it less short and
mowing more often.
Mowing (fig. J1 & J2)
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
Place the bulk of the mains cable on the lawn, close to the
u
starting point (position 1 in fig. J1).
Switch the appliance on as described above.
u
Proceed as shown in fig. J1
u
Move from position 1 to position 2.
u
Turn right and proceed towards position 3.
u
Turn left and move towards position 4.
u
Repeat the above procedure as required.
u
Warning! Do not work towards the cable as shown in fig. J2.
Note: Use the cable retention clips (4a) to secure the cord
running from the deck to the on switch neatly to the handle
assembly, as shown in figure K.
Cleaning
Turn the mower off and let the blade come to a stop. Use only
mild soap and a damp cloth to clean the mower. Clean out any
clippings which may have accumulated on the underside of
the deck. After several uses, check all exposed fasteners for
tightness.
Preventing corrosion
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilizers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
Turn the mower off and unplug mower. Wipe all exposed parts
with a damp cloth.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
12
(Original instructions)
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage V
AC
Power inpurt W
No-Load speed min
-1
Weight Kg
Hand/arm weighted vibration value:
= ah <2.5 m/s , uncertainty (K) = 1.5 m/s
2
Sound pressure level at the operator's ear:
L : 84,0 dB(A); K= 2,5 dB(A)
PA
Sound power level L
EC declaration of conformity
%
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
BEMWH551 Hover mower
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60335-1:2012 + A11:2014,
EN 50636-2-91:2014
BEMWH551
.
2
: 95 dB(A); K= 1.0 dB(A)
WA
230
1200
6500
5.5