Translation Of Original Operating Instructions - Rupes LH16ES Traduction Des Instructions Originales

ENGLISH
PICTOGRAPH
TECHNICAL SPECIFICATIONS
TYPE
INSULATION CLASS
POWER
n NOMINAL RPM
ELECTRONIC SPEED CONTROL
BUFFER PAD AND BUFFER DIAMETER MAX
SPINDLE THREAD
WEIGHT according to EPTA-Procedure 01/2003
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary. Refer to the label technical
specifications to the nominal values of the tool.
WARNINGS
The safety and accident prevention instructions are reported
in the "SAFETY INSTRUCTION" booklet which is an integral
part of these documents. This operating instructions manual
indicates the additional information required for the specific
use of the tool.
CORRECT USAGE
This tool is designed to be used as a polisher. Read all the
warnings, instructions, indications provided on drawings
and specifications supplied with this tool. Failure to comply
with all the instructions provided below may cause electrical
shocks, fire and/or serious injuries.
This tool is not intended to be used for smoothing, metal
brushing and cutting operations. The use of this tool for
unintended applications may cause hazards and injuries to
people.
The tool must be used with accessories that have been
specifically designed or recommended by the manufacturer.
The fixing of the accessory to the tool does not guarantee a
safe operation.
The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories
with incorrect dimensions cannot be adequately protected or
controlled.
Warning symbol/ Warning message
Read instruction manual
Wear eye protection
Wear ear protection
Wear a mask
Wear a gloves
CE compliant
EurAsian Mark
Italian Quality Mark
C-Tick Mark
Disposal of decommissioned
Arrow
W
/min
Kg

TRANSLATION OF ORIGINAL OPERATING INSTRUCTIONS

Act in the direction indicated by the arrow direction
LH16ES LH18ENS
/ II / II
900 1100
700 - 1.700 750 ÷ 1.850
YES YES
178 200
M14 M14
2,0 2,2
The configuration of accessories must match the tool.
The use of accessories that cannot be perfectly fitted on the
tool may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool or
accessory has fallen, verify that it is not damaged or install
a new accessory. After inspecting or installing an accessory,
test the operation of the tool at maximum speed and without
load for one minute, keeping at a safety distance. If the
accessories are damaged, they will break during this test.
Wear personal protective equipment. According to the
the application, use face shield, mask or safety goggles.
According to the case, wear a dust mask, ear protection,
gloves and a smock capable of stopping small abrasive
fragments of the work piece. Eye protection must be able
to stop flying bits produced from the different operations
The dust mask or the respirator must be capable of filtering
particles produced by your work. Prolonged exposure to
high intensity noise can cause a loss of hearing. Keep the
people present at a safety distance with respect to the work
area. Anyone entering the work area must wear personal
protection equipment. The fragments of the work piece or
the broken accessories can fly off and cause injuries in the
immediate vicinity of the work area. Keep the tool only for
isolating gripping surfaces, while the operations are carried
out in which the cutting accessory may be in contact with
the hidden cables or with its cable. The contact between the
ISO7010 - W001
ISO7010 - M002
ISO7010 - M004
ISO7010 - M003
ISO7010 - M016
ISO7010 - M009
LH22N LH22EN
/ II
1020 1020
2.000 900 ÷ 2.000
YES YES
200 200
M14 M14
3,4
7
/ II
3,4