Diamond Blades; General; Soff-Cut 150; Soff-Cut 150 D - Husqvarna Soff-Cut 150 Manuel D'utilisation

General

CAUTION! Inspect the blade for damage,
!
cracks, loss of segments, warping,
overheating, excessive wear or a damaged
tri-arbor hole. If the blade shows any of
these problems, discard the blade.
Make sure the blade is marked with a
maximum operating speed greater than 4450
rpm.

Soff-Cut 150

Use only Husqvarna Excel Series blades or blades marked
with a maximum operating speed greater than 4450 rpm.
Excel Series blades
CAUTION! Husqvarna Excel Series diamond
!
blades are designed to only cut green
concrete. Cutting any other material may
result in blade failure or a dangerous
condition.
The Excel Series are designed specifically for the Soff-Cut
Ultra Early Entry dry cutting system of green concrete.
These specialty blades are designed to increase speed and
life while cutting a wide range of aggregates.
Choose the correct blade for your application. If you are
uncertain of what blade to use contact your local service
dealer.
Excel 1000
XL6-1000
purple
Excel 2000
XL6-2000
green
Excel 3000 red XL6-3000
Excel 4000
XL6-4000
orange
Excel 5000
XL6-5000
yellow
Excel 6000
XL6-6000
black

Soff-Cut 150 D

Use only Husqvarna ProEdge Series blades or blades
marked with a maximum operating speed greater than 4450
rpm.
ProEdge series blades
The ProEdge Line is designed for architectural scoring to
replace labor-intensive hand tooling ideal for residential and
commercial applications.
The blades are used to chase standard joints and turns
ragged, chipped or raveled saw joints into beautifully beveled
or radius edges.
10 –
English

DIAMOND BLADES

Ultra hard aggregate and
non abrasive sand.
Hard to ultra hard aggregate
and non abrasive sand.
Hard aggregate, medium
abrasive sand.
Medium hard aggregate,
medium abrasive sand.
Medium hard to soft
aggregate, abrasive sand.
Soft aggregate, highly
abrasive sand.
Chasing cuts using the ProEdge blades would begin the next
day or later after the concrete is placed and control joints have
been made.
Choose the correct specification of blade for your application.
If you are uncertain of what blade to use contact your local
service dealer.
ProEdge V-
XL6-V21-D
blade
XL6-V23-D
XL6-V25-D
XL6-V500-D
ProEdge
XL6-R250-D
Radius blade
XL6-R500-D
The correct specification of ProEdge Blade is based on the
width of the pre-existing control joint as follow:
XL-V21 XL-V23
3/8" 5/8"
1/8"
Existing
Joint
.100" - .120"
XL-V38
3/4" 1"
1/4"
Existing
Joint
.380"
XL-R250 XL-R500
5/8" 3/4"
R .250"
Existing
Joint
.100" - .120"

Transport and storage

• Remove the blade before transportation or storage of the
machine.
• Store the blade in a dry place.
• Inspect new blades for transport or storage damage.
3/8" (9.53mm) wide bevel
blade for existing 0.100"
(2.54mm) wide saw cut.
5/8" (15.88mm) wide bevel
blade for existing 0.100"
(2.54mm) wide saw cut.
5/8" (15.88mm) wide bevel
blade for existing 0.250"
(6.35mm) wide saw cut.
1" (25.4mm) wide bevel blade
for existing 0.500" (12.7mm)
wide saw cut.
5/8" (15.88mm) wide bevel
blade for existing 0.100"
(2.54mm) wide saw cut.
3/4" (19.1mm) wide bevel
blade for existing 0.100"
(2.54mm) wide saw cut.
XL-V25
5/8"
1/4" 3/16"
Existing Existing
Joint Joint
.100" - .120" .250"
XL-V500
5/16"
Existing
Joint
.500"
R .500"
Existing
Joint
.100" - .120"