Kinomap App - Christopeit Sport AX 7000 Notice De Montage Et D'utilisation

Remark:
1. During body fat test, it will display Err2 if hand pulse sensors get no-
input.
2. According to test result, 10 seconds have no operation or operation
arbitrarily key, will get into system recommendation to toughen pro-
gram.
TEST-Pulse Recovery:
It is a function to check the condition of pulse recovery that is scaled
from 1.0 to 6.0 while 1.0 means the best and 6.0 means the worst and
the increment is 0.1. In order to get rated correctly, users must test it
right after the workout finished by pressing „TEST" key and then stop
exercising. After the key is pressed, please also apply the heart rate de-
tector appropriately. The test will last for 1 minute and the result will
show in the display.
PULSE
1. Pulse Rate:
The whole set of heart rate detector include 2 sensors each side. Each
sensor has 2 pieces of metal parts. The correct way to get detected is
to gently hold both metal parts each hand. With the good signals pi-
cked up by the computer, the heart mark in the HEART RATE Display
shall flash. Sometimes the heart rate value is not useable, based on
wet hands or any other contact problems during exercising. If you need
high accuracy heart rate value you have to use an external heart rate
measurement with a pulse belt.
"WARNING" Heart rate monitoring system may be inaccurate. Over
exercise may result in injury or death. If you feel faint stop exercising
immediately.
WATT TABELLE
RPM and Power in Watt of Level 1 - Level 24 for AX 7000
Art.-Nr. 1908
LEVEL 20 RPM 30 RPM
WATT WATT
1
7 15
2 9 18
3 10 20
4 11 22
5 12 25
6
14 27
7 15 30
8 16 33
9 18 36
10 19 38
11 20 41
12 22 43
13 23 46
14
24 49
15 26 52
16 27 55
17 28 58
18 30 62
19
31 65
20 32 68
21 34 71
22 35 74
23 36 77
24 38 80
Remarks:
1.The power consumptions (Watt) are adjusted by measuring the dri-
ving speed (min-1) of axle and the braking torque (Nm).
2.Your equipment was tested to fulfill the requirements of its accuracy
classification before shipment, If you have doubts about the accuracy,
please contactwith your local retailer or send it to accredited test labo-
ratory to ensure or calibrate it.
(Please note that a deviation tolerance as noted on page 15, is permis-
sible.)
Error Messages
Each time the computer is restarted, it will run a quick test for functio-
nality. If something is not okay, it indicates possible errors:
E 1 This symbol and a warning tone appear if the wiring is incorrectly
connected or there is a fault in the resistance setting. Check all cable
connections, especially at the connectors. After eliminating the error,
press and hold the „Start / Stop" button for 2 seconds to reset the sys-
tem to 0.
22
40 RPM 5 0 R P M 60 RPM 70 RPM
WATT WATT WATT WATT
19 33 40 43
24 40 50 55
29 46 60 67
34 54 70 82
39 61 80 93
44 68 90 106
49 74 100 118
53 81 110 130
59 88 120 143
64 95 130 155
69 103 140 167
73 110 150 180
79 117 160 191
84 124 170 205
89 132 180 220
94 140 190 235
99 149 200 251
104 157 210 267
109 164 220 279
114 172 230 290
120 179 240 301
127 186 250 314
133 193 260 330
139 201 270 345
GB
80 RPM
WATT
61
76
90
107
125
140
155
171
186
202
218
232
250
268
286
304
323
342
356
370
388
406
420
438