Introduction; Device Description - Parkside PBK 4 B3 Consignes D'utilisation Et De Sécurité

2. Introduction

Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope your new tool brings you much enjoyment and success.
Note:
In accordance with the applicable product liability laws, the manufactur-
er of this device assumes no liability for damage to the device or caused
by the device arising from:
• Improper handling,
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Application other than specified,
Please consider:
Read through the complete text in the operating manual before installing
and commissioning the device.
The operating manual is intended to help the user to become familiar
with the machine and take advantage of its application possibilities in
accordance with the recommendations.
The operating instructions include important instructions for the safe,
proper and economic operation of the machine, for avoiding danger, for
minimising repair costs and downtimes and for increasing the reliability
and extending the service life of the machine.
In addition to the safety instructions in this operating manual, you must
also observe the regulations applicable to the operation of the machine
in your country.
Keep the operating manual package with the machine at all times and
store it in a plastic cover to protect it from dirt and moisture. They must be
read and carefully observed by all operating personnel before starting
the work. The machine may only be used by personnel who have been
trained to use it and who have been instructed with respect to the associ-
ated hazards. The required minimum age must be observed.
In addition to the safety instructions in this operating manual and the
separate regulations of your country, the generally recognised technical
rules relating to the operation of such machines must also be observed.
We accept no liability for accidents or damage that occur due to a fail-
ure to observe this manual and the safety instructions.
Familiarise yourself with the operating manual before attempting to oper-
ate the device.

3. Device description

1. Motor drive unit
2. Lifting eye
3. On/Off switch
4. Switch lock
5. Rear handle
6. Spark plug connector
7. Starter cable
8. Fuel tank
9. Throttle
10. Front handle
10a. Pins
11. Locking screw engine drive unit
6 GB/IE/NI
Scythe attachment (PBK 4 B3-2)
12. Brush cutter / grass trimmer
13. Brush cutter / grass trimmer locking pin
14. Brush cutter / grass trimmer shield
14a. Brush cutter / grass trimmer cutting blade shield
15. Cutting blade
15a. Cutting blade protection
16. Thread coil
16a. Trigger
Hedge trimmer attachment (PBK 4 B3-3)
17. Hedge trimmer
18. Hedge trimmer locking pin
19. Adjustment lever
20. Cutting unit
21. Hedge trimmer protection
22. Extension attachment
23. Extension attachment locking pin
24. Drive shaft
25. Extension attachment locking screw
Pole pruner attachment (PBK 4 B3-4)
26. Pole pruner
27. Pole pruner locking pin
28. Protective ring
29. Oil tank
30. Blade fixing nut
31. Saw chain
32. Blade
33. Bench grinder aid
34. Pole pruner protection
35. Carrying strap
36. Oil-petrol mixing bottle
37. Replacement thread
38. Tool bag
39. Spark plug wrench
40. Allen key size 4
41. Allen key size 5
42. Rubber ring
43. Retaining clip
44. Threaded pins
45. Wing nut
46. Positioning hole
47. Screw (pre-mounted)
48. Internal flange
49. Threaded mandrel
50. External flange
51. Cover
52. Nut
53. Chain cover
54. Chain wheel
55. Chain tensioning screw
55a. Chain tensioning bolt
56. Oil tank cover
57. Protection screw engine drive unit
58. Cutting device protective cover
59. Protection screw extension attachment
60. Choke lever