Publicité
Les langues disponibles
Les langues disponibles
5.
Draw the Cable (66) downwards between the two Guiding Tube (5) and fully thread the bolt on the end of the
Cable (66) into the top opening on the Select Bar (12).
6.
Attach the Lat Bar (13) to the front end of the Cable (66), connect by X1 Hook (61).
STEP 7
1.
Attach one end of the Cable for Butterfly Arm
(64) to the hook on the Right Butterfly Arm
(10R), tighten by X1 Hex Head Bolt (22), X1 Flat
Washer (33) and X1 Nylon Nut (37).
2.
Draw the Cable (64) around the Pulley (48) then
attach the Pulley (48) to the Pulley Bracket A
(17) on right side of the Upright Support Tube
(2), tighten by X1 Hex Head Bolt (26) and X1
Nylon Nut (38).
3.
Draw the Cable (64) downward and around the
Pulley (48), attach the Pulley (48) to the upper part
of Two Way Bracket for Pulley (21) and tighten by
X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
4.
Draw the Cable (64) upward and around Pulley
(48). Attach Pulley (48) to the Pulley Bracket
(17) on the left side of the upright Support Tube
(2), tighten by X1 Hex Head Bolt (26) and X1
Nylon Nut (38).
5.
Attach the other end of Cable (64) to the hook
on the Left Butterfly Arm (10L), tighten by X1
Hex Head Bolt (22), X1 Flat Washer (33) and X1
Nylon Nut (37).
36
STEP 8
1.
Attach the end with stopper ball of Cable for Lower Pull Bar (65) to the open bracket of Leg Curl (7), around the
under side of Pulley (48), tighten the Pulley(48) with the bracket by X1 Hex Head Bolt (28) through X2 Plastic
Bushing (46) (each side), X2 Falt washer(24) (each side) and X1 Nylon Nut (38).
2.
Draw the Cable (65) through the opening space on the lower part of Upright Support Tube (2), around the
Pulley (48) from under side then attach the Pulley (48) to Bracket C on the Base Frame (1), tighten by X1 Hex
Head Bolt (26) and X1 Nylon Nut (38).
3.
Draw the Cable (65) upward and around the upper side of Pulley (48). Attach the Pulley (48) to the under side of
the Bracket for Pulley (16), tighten by X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
4.
Draw the Cable (65) downward and around the under side of Pulley (48). Attach the Pulley (48) to bracket D
on the Base Frame (1) and tighten by X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
5.
Draw the Cable (65) upward and around the upper side of Pulley (48). Attach the Pulley (48) to the under side of
Bracket for Pulley B (20) set and tighten by X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
6.
Draw the Cable (65) downward and connect with bracket E on Base Frame (1) by Chain 7 Links (59) and X1
Hook (61). Note: Adjust the Cable (65) to be tighten enough and lock on certain position of Chain (59) by
Hook (61).
7.
Attach the Lower Pull Bar (14) to the front end of Cable (65), connecting by Chain 6 Links (60).
GYM-100
37
EN
Publicité
