FITFIU FITNESS GYM-100 Manuel D'instructions page 18

STEP 3
1. Place the Guiding Tube (05) into the Bridge
Tube (08) and tighten by X2 Flat Washer (33)
and X2 Hex Head Bolt (22).
2. Attach the Bridge Tube (08) to the Upright
Support Tube (02) and tighten by X2 Hex
Head Bolt (30), X4 Flat Washer (34) and X2
Nylon Nuts (38).
STEP 4
1. Attach the Seat Support Tube (06) to the
Upright Support Tube (02), tighten by X2 hex
Head Bolt (30), X4 Curve Washer (34) and
X2 Nylon Nuts (38).
2. Attach Backrest Cushion (57) into Upright
Support Tube(02), tighten by X2 Hex Head
Bolt (25) and X2 Flat Washer (34) through the
thread holes on the Backrest Cushion (57).
3. Attach the seat (58) to Seat Support Tube(06)
tighten by X2 Hex Head Bolt (24) and X2 Flat
Washer(34) through the thread holes on the
back side of Seat (58).
4. Screw-in the Small Rubber Stopper (52) into
the front side of Seat Support Tube (06).
5. Attach the Leg Curve Tube (07) to the front
side of Seat Support Tube (06), tighten by
X1 Hex Head Bolt (29), X2 Flat Washer (35)
and X1 Nylon Nut (39).
6. Attach the Foam Tube for Leg Curl (15) into
the holes on Leg Curl Tube (07) and front/
upper bracket of Seat Support Tube (06).
7. Attach the Foam for Leg Curl Tube (54) onto the
2 sides of each Foam Tube for Leg Curl (15).
34
STEP 5
1. Attach the Pull Unit (09) to the Bridge Tube (08), insert the Axle for Pull Unit (19) through X4 Powder Metal
Ring (31), X2 Flat Washer (35) and tighten by X2 Nylon Nuts (39).
2. Attach the Butterfly Arm R (10R) to the right side of Pull Unit (09) through X2 Powder Metal Ring (31) and X1
Flat Washer (35) and tighten by X1 Nylon Nut (39).
3. Do the same procedure for the
Butterfly Arm L (10L) to the Pull Unit
(09) by same parts.
4. Attach the Connecting Bolt (18) onto
the Upright Support Tube (02), tighten
by X1 Hex Head Bolt(23), X2 Flat
Washer (37). Put the Knob (67) onto
the Connecting Bolt (18) by through
Flat Washer (36).
5. Put the Foam for Butterfly Arm (53)
onto the R/L Butterfly Arm (10R &
10L) and adjust to certain position.
6. Attach the Handlebar (11) onto the
Butterfly Arm R (10R), tighten by X1
Curve Washer (33) and X1 Hex Head
Bolt (22). Do the same procedure of
Butterfly Arm L (10L) with the other
Handlebar (11).
7. Attach the Pulley Bracket (17) onto
the 2 sides of Upright Support Tube
(02), tighten by X2 Hex Head Bolt
(24), X2 Flat Washer (35) and X2
Nylon nuts (37) for 2 sides. 1)
STEP 6
1. Attach the Cable for Lat Bar (66) to the opening bracket at the front of the Bridge Tube (8). Note: The ball
stopper of the Cable (66) should be underneath the Bridge Tube (8). Attach the Cable (66) onto the Small
Pulley (49) and put the Cap for Small Pulley (50) to the two side of Small Pulley (49). Note: The Cable (66)
has to come out of the Cap (50) from the opening sides. Tighten to the bracket by X1 Hex Head Bolt (27)
and X1 Nylon Nut (38).
2. Draw the Cable (66) towards the back side of the machine through the upper opening of Upright Support
Tube (2) and around Pulley (48), then attach the Pulley (48) onto bracket A as drawing, tighten by X1 Hex
Head Bolt (26) and X1 Nylon Nut (38).
3. Draw the Cable (66) downwards and around Pulley (48). Attach the Pulley (48) with the Bracket for Pulley
(20) on two sides then tighten by X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
4. Draw the Cable (66) upwards and around Pulley (48). Attach the Pulley (48) to bracket B(20) and tighten by
X1 Hex Head Bolt (26) and X1 Nylon Nut (38).
GYM-100
35
EN