Oursson MO2305 Manuel D'instructions page 15

POSITION, Pic. A-2
• Place the device on a flat horizontal heat resistant
surface, high from children's reach, keeping the
distance from walls/furniture. One side must be
completely free. It is forbidden to embed this
device.
• Do not place the working device under/near curtains
or other flammable materials, as this may cause a fire.
PRODUCT SET, Pic. B
Body...........................................................................1 ps.
Enameled pan........................................................1ps.
Grid.......................................................................1ps.
Handle for pan and grid.........................................1ps.
Handle for spit........................................................1ps.
Spit...................................................................1ps.
Round pan 9"/22,8 cm............................................1ps.
The crumb tray for lids.............................................1ps.
Fish basket............................................................1ps.
8
Grill-basket.........................................................1ps.
9
Instructions manual.......................................................1 ps.
ELEMENTS OF DESIGN, Pic. C-1
1
Door handle
Spit bracing
2
3
Slots for grid and pans
4 Door
Control panel
5
6
Ventilation openings
7
Work indicator
Removable tray for crumbs
8
Inner backlight, Pic. C-1-2
Upper and lower heating elements, Pic. C-1-1
UTILIZATION
Control panel, Pic. C-2
Function switch, Pic. C-2-4
• STOP position, turning off the convection / spit op-
eration
• Convection (hot air circulation around the product)
• Spit (spit rotates, uniformly browning on all sides)
• Convection and spit
Temperature regulator, Pic. C-2-1
• Adjusting the temperature from 100°C to 230°C
Р
Preparation mode switch. Pic. C-2-2
• STOP position
• Upper heating element (upper heating)
• Lower heating element (lower heating)
• Upper and lower heating elements, imultaneous
operation of both upper and lower heating ele-
ment.
• Upper heating element and spit.
(For MO2305, MO2610 models)
Timer, Pic. C-2-3
• Timer, time selection from 0 up to 60 minutes.
• STOP position, utilized for stopping the cooking
process.
Spit construction, Pic. C-5
Hook
1
Clamp
2
Fastener
3
4 Bayonet
5
Motor coupling
Preparation for operation
Before first use, wipe the body with a soft, dry cloth.
Wash the other parts with warm water and detergent.
Before assembling or disassembling the make sure that
the device is unplugged. Thoroughly dry all parts.
Turn on the empty device for 15 minutes, set the maximum
, mode, to remove the smell of a new
temperature in
device. Ventilate the room. Allow the device to cool.
Order of operation, Pic. C-2
1. Make sure that the crumb tray is completely installed,
and timer knob
is set in the
device.
2. Set the required temperature with the
3. Turn on the timer
the device to heat up. Timer knob will turn automatically
in the cooking process.
4. Choose a required mode with the help of corresponded
regulators:
5. Place prepared beforehand products on the pan/grid/
spit. Do not place products closer than 2 cm. from the
heating elements.
6. Carefully install grid, pan or spit into the device, Pic.
C-3. Close the door.
7. Turn on the timer
recommended to open the door in the preparation
process.
NOTE: When the device is working, the inner backlight is
on and working indicator
8. When the preparation process is completed, the timer
(device) turns off automatically, you will hear a sound
signal. Set all the regulators into the
9. Carefully open the door and take out prepared product
with the help of potholders or a special handle for pan,
Pic. C-4.
position. Plug in the
regulator.
for 5 minutes in the , mode, for
, setting the required time. It isn't
, Pic. C-1 is flashing.
position.
15