Maytag W11355748A Guide De Démarrage Rapide

OPERATING INSTRUCTIONS
WARNING
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil
on it (including cooking oils).
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in
death or fire.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in
death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to persons,
read the IMPORTANT SAFETY INSTRUCTIONS, located in your
appliance's Owner's Manual, before operating this appliance.
Button Descriptions
1. POWER/CANCEL
Touch to turn the dryer on and off. Touch to stop/cancel a cycle at any
time.
2. CYCLE CONTROL KNOB
Use the Cycle Control knob to select available cycles on your dryer. Turn the
knob to select a cycle for your laundry load. See the online "Cycle Guide" for
details.
3. START/PAUSE
Touch and hold until the LED comes on to start a cycle, or touch once while a
cycle is in process to pause it.
4. TIMED DRY ADJUST
Touch "+" or "–" with Timed Dry Cycles to increase or decrease the length of a
Timed Dry or Rapid Dry cycle.
5. LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and the estimated time
remaining (for Sensor cycles) or actual time remaining (for Timed cycles) will
be displayed. Touch the setting names next to the display to adjust settings.
See online "Cycle Guide" for details. Not all settings are available with all
cycles.
Temperature
When using Timed Cycles, you may select a dry temperature based on the
type of load you are drying. Use the warmest setting safe for the garments in
the load. Follow garment label instructions.
NOTE: Sensor Cycles allow temperature adjustment. At most, 3 of available
temperatures (not including Air Only) are allowed.
Dry Level
You may adjust the Dry Level on Sensor cycles (except for the Sanitize cycle).
NOTE: Dryness level is for use with Sensor Cycles only.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch Wrinkle Prevent to
add up to 150 minutes of periodic tumbling to help reduce wrinkling. On some
cycles, you may select the "With Steam" setting to add a short steam cycle after
60 minutes to help smooth out wrinkles.
NOTE: If you open the dryer door prior to the end of the Wrinkle Prevent, the
dryer will go into Pause mode. You will need to touch Power to turn off or touch
Start/Pause to continue Wrinkle Prevent.
6. OPTIONS
Use to select available options for your dryer. Not all cycles and options are
available on all models.
Audio Level
Touch Audio Level to change end beep and button sounds to low, high, or off.
W11355748A
W11355964A-SP
Dryer Quick Start Guide
Step 1. Clean Lint Screen
Step 2. Load Clothes; then Close
Door
Step 3. Power On/Cancel
Step 4. Select Cycle and Settings
Step 5. Press Start/Pause
Not all features, cycles, and options are available on all models. Appearance may vary.
NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control
panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name.
Energy Saver
Activate the Energy Saver setting to increase your energy savings. This setting uses a
lower heat level and extends cycle time. Turn on for optimal energy savings. Turn off
for optimal cycle times. Energy Saver will default on for Normal cycle.
Static Reduce (on some models only)
Touch to add the Static Reduce option to selected Sensor Cycles.(see online "Cycle
Guide" for details). The dryer will automatically tumble, pause, and introduce a small
amount of moisture into the load to help reduce static. This option adds approximately
8 minutes to the total cycle time.
Damp Dry Signal
Touch to select the Damp Dry Signal. When selected, a series of beeps will sound
when the load is damp, but not completely dry. This will allow you to take clothes out
of the load that do not need to dry completely. This option is not available on Sanitize,
Steam Refresh, and the Timed Dry cycles.
7. CYCLE STATUS
The Cycle Status indicators show the progress of a cycle. See the online "Cycle
Guide" for details.
Sensing
The Sensing indicator will light during Sensor Cycles to indicate that the moisture
sensor on the dryer is operating. This indicator will not light during Timed Cycles or
options such as Wrinkle Prevent.
Cycle Guide – Normal Cycle
Senses moisture in the load and shuts off when the load reaches the selected dryness level. The dry temperature
shown is the default temperature. This setting can be modified on some cycles but is not retained for future drying
with this cycle. The dryness setting can be changed on some cycles and will be retained for future drying with this
cycle.
To get the most energy savings and enhanced fabric care from your dryer, use the Sensing cycles. These cycles
measure the drying air temperature and moisture levels to turn the dryer off once the load reaches the selected
dryness level. For electric models, dryer performance and results may vary with service voltage less than 240V.
Items to Dry: Cycle: Temperature:
Work clothes, Normal Medium
casual wear, mixed
cottons, sheets,
corduroys
NOTE: Government energy certifications for this model were based on the Normal cycle, Maximum Dry, and
Energy Saver on. The as-shipped defaults of Wrinkle Prevent off and Energy Saver on were used.
Online Ordering Information
For detailed installation instruction and maintenance information, winter storage, and transportation tips, please
see the Owner's Manual included with your machine.
For information on any of the following items, the full cycle guide, detailed product dimensions, or for complete
instructions for use and installation, please visit https://www.maytag.com/owners, or in Canada
https://www.maytag.ca/owners. This may save you the cost of a service call.
However, if you need to contact us, use the information listed below for the appropriate region.
United States:
1–800–344–1274
Maytag Brand Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022–2692
Check Vent
The Check Vent indicator will light if there is a blocked vent or low
airflow.
Good Airflow
This indicator will light if there is no major vent blockage.
Steam
This indicator will light when a steam function is active.
NOTE: Steam is not available on all cycles or models.
Done
This will indicate that the selected cycle has ended and the load may be
removed from the dryer. If Wrinkle Prevent has been selected, the dryer
may continue to tumble the load, even if the Done indicator is lit.
Check Lint Screen
The Check Lint Screen indicator light will flash as a reminder to clean
the lint screen. It will flash until the door is opened or a cycle is started. It
will turn off when the dryer is turned off.
Description:
Starts at High heat, quickly goes to Medium High, and
then ends on Medium heat to dry large loads of mixed
fabrics and items. Normal is the preferred energy
cycle. Energy Saver defaults on. To reduce cycle time,
at the cost of energy savings, turn Energy Saver off.
Canada:
1–800–688–2002
Maytag Brand Appliances
Customer eXperience Centre
200–6750 Century Ave.
Mississauga, Ontario L5N 0B7