Publicité
Les langues disponibles
Les langues disponibles
PRODUCT MAINTENANCE
So as to make sure that the automated unit functions for as
long as possible and in complete safety, you need to per-
form scheduled maintenance every 6 months. To perform
maintenance checks, repeat the procedure described in Chapter 4.1 -
Inspection.
ATTENTION! – Before carrying out any check, disconnect any
electrical power input source.
DISPOSAL OF THE PRODUCT
This product is an integral part of the automation and
therefore must be demolished with it.
As for installation, the plant must also be demolished by
qualified staff at the end of its life span.
This product is made up of various types of materials: some can be re-cy-
cled, others must be disposed of. Obtain information regarding recycling
or disposal systems envisioned by the Standards in force on your territory
for this category of product.
Attention! – some parts of the product can contain pollutant or dan-
gerous substances which, if dispersed into the environment, could have
damaging effects on the same and human health.
As indicated by the symbol at the side, it is prohibited to
throw this product into domestic waste. "Separate col-
lection" must be performed for disposal, according to the
methods envisioned by the Regulations in force on your ter-
ritory or take the product back to your dealer on the pur-
chase of a new equivalent product.
Attention! – local regulations in force may envision heavy sanctions if this
product is disposed of abusively.
CE declaration of conformity and declaration of
incorporation for a "quasi-machine"
Declaration in accordance with Directives: 2014/30/UE (EMC); 2006/42/EC
(MD) annex II, part B.
Note - The content of this declaration corresponds to the declaration made in the
official document filed in the offices of Nice S.p.a., and particularly the latest version
thereof available prior to the printing of this manual. The text contained here has
been adapted to meet editorial requirements. A copy of the original declaration may
be requested from Nice S.p.a. (TV) I.
Declaration number: 569/WI1
Name of manufacturer: NICE S.p.A.
Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy.
Person authorized to provide technical documentation: NICE S.p.A. – Via
Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy.
Product type: 24Vd.c. electro-mechanical gear motor for swing gates.
Model / Type: WI1
Accessories: No accessory.
The undersigned Roberto Griffa, as Chief Executive Officer, hereby declares under
his own responsibility that the products identified above comply with the provisions
of the following directives:
• DIRECTIVE 2014/30/UE OF THE EUROPEAN PARLIAMENT AND COUNCIL of
February 26 2014 concerning alignment of Member States' legislation regarding
electromagnetic compatibility (consolidated text), according to the following har-
monized standards: EN 61000-6-2:2005; EN 61000-6-3:2007 + A1:2011.
The product also complies with the following directive in accordance with the re-
quirements for "quasi-machines":
• Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of
Revision: 0 Language: EN
PRODUCT TECHNICAL FEATURES
RECOMMENDATIONS • All technical features stated make reference at
a room temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to
modify the product at any time it deems necessary, however maintaining
the same functionality and destination of use.
n Type: Electro-mechanical dear motors for gates and doors with hinged
panels. n Power input: 24 V
mum absorption: 2.9 A n Nominal power: 25 W n Maximum power:
70 W n Protection rating: IP 67 n Run: 0°...120° (±10°) n Nominal
speed: 1.5 rpm n Nominal torque: 60 Nm n Maximum torque: 150
Nm n Functioning temperature: -20°C...+50°C n Cycles/hour at the
nominal torque: 60 n Dimensions: 305 x 145 x 346 n Weight (kg):
5.5
May 17 2006 regarding machines and amending directive 95/16/EC (consolidat-
ed text).
– I declare that the pertinent technical documentation has been prepared in ac-
cordance with Annex VII B to Directive 2006/42/EC and that the following essen-
tial requirements have been met: 1.1.1 - 1.1.2 - 1.1.3 - 1.2.1 -1.2.6 - 1.5.1 -1.5.2
- 1.5.5 - 1.5.6 - 1.5.7 - 1.5.8 - 1.5.10 - 1.5.11.
– The manufacturer agrees to send the national authorities pertinent information on
the "quasi-machine" in response to a motivated request without affecting its in-
tellectual property rights.
– If the "quasi-machine" is operated in a European country with an official language
other than the language used in this declaration, the importer must associate a
translation with this declaration.
– The "quasi-machine" must not be operated until the final machine in which it is
to be incorporated is declared to conform to the provisions of Directive 2006/42/
EC, if applicable to it.
The product also complies with the following standards: EN 60335-1:2002 +
A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011;
EN 60335-2-103:2003 + A11:2009.
The parts of the product which are subject to the following standards comply
with them: EN 13241-1:2003 + A1:2011; EN 12445:2002; EN 12453:2002; EN
12978:2003 + A1:2009.
Oderzo, April 21 2016
n Nominal absorption: 1 A n Maxi-
Eng. Roberto Griffa
(Chief Executive Officer)
English – 3
Publicité
