Publicité
Les langues disponibles
Les langues disponibles
LEVEL
MASTER
2ND MASTER VOLUME
REMOTE1
™
offers you a second master volume, that can be activated
When other functions-patch, such as the PowerSoak
per footpedal in Direct-Access-Mode, and can be adjusted (reduced)
activated, use the Level-Control to regulate the currently active
in a 10dB range. Now you can use all your sounds at two different
functions-patch.
volumes.
Turning off, or switching to another functions-patch automatically stores
1. Master Volume on : Rhythm volume
your setting.
2. Master Volume off : Solo volume
When you press the MasterVolume button on the REMOTE1
™
, the
dial knob next to it is activated. Use this Level-Control to set the Master
Volume.
By pressing the the REMOTE1
™
MasterVolume again you switch back
-5 dB
to full volume.
Any volume for your presets
The REMOTE1
™
can store all of your settings, including every Master-
Volume preference to one of the 36 presets. This allows you to store any
volume required for your sound, in the Preset-Mode.
The Level-Control sets the 2nd MasterVolume Level when the
MasterVolume switch
8
is lit.
The Level Control:
-10 dB
0 dB
controls the 2nd Master, PowerSoak
and Gain / Clean Volume patches.
Volume reduction in „2nd Master"
POwER SOAK
9
or Gain are
For many, there is nothing better than the sound of a totally cranked tube
You will notice when playing that only the loud peaks are being sup-
amp with a saturated output. The volume necessary to achieve this is
pressed and turned into compression and light overdrive. If you turn up
usually unbearable. Resourceful technicians have developed something
the Master Volume knob on the AMP1
to reduce the output: the PowerSoak.
sound overdrive that only an overdriven poweramp can give you.. If you
turn Level-Control knob on the REMOTE1
When PowerSoak
9
is activated, the Level-Control knob controls two
you will distinctly hear it jump into the Home section. You are now at 2
sections:
watts. More than loud enough for home use! You can turn the level knob
Home (0.15 – 2 watts) and Stage (7 – 100 watts), see graphic.
even further, until the sound is completely flat gone. The lower you go,
the more overdrive you get. It's really worthwhile to experiment with the
The PowerSoak's range of effect depends upon the strength of the
Master Volume on the AMP1
signal it is getting, depending on the Master Volume on the AMP1
™
.
To get acquainted with the PowerSoak, it is recommended to play with
a clean sound, with the Master Volume set at 5. Attention, 5 is already
very loud, and then slowly reduce the level of the PowerSoak using
the Level-Control knob on the REMOTE1
™
. Just before reaching the
center position, you are still getting 7 watts. This might be too loud for
home use, but with a band you will certainly need a little output. That's
why the 7 – 100 watt section is called Stage.
The PowerSoak works in 2 sections:
home, from 150 milliwatts to 2 watts
Stage, from 7 to 100 watts
PowerSoak output sections
MIDI OUT
REMOTE1
™
has a MIDI OUT jack, that can be used to integrate and control external MIDI effect devices in your setup. To take advantage of this
feature, use a MIDI cable to connect MIDI OUT on the REMOTE1
™
, you get the fat smooth
Every preset in the REMOTE1
sends a fixed MIDI Program Change Command to the MIDI OUT jack (on MIDI channel 2) to switch between
™
™
past the center position,
programs on your external MIDI device. The MIDI commands in the REMOTE1
using MIDI Learn or Midi-Mapping in the Midi device itself.
Here is the REMOTE1
™
chart, showing the MIDI-PRG-Change-Commands: (for example: Bank 3, Preset 6: MIDI-PRG-Change-Command 24)
Make sure your external MIDI device is set to MIDI-receive channel 2.
™
and the PowerSoak setting.
Preset
1
2
Bank 1
01
02
Bank 2
10
11
Bank 3
19
20
Bank 4
28
29
1
2
3
4
LOOPERKIT
REMOTE1
™
is the first amp footcontroler that can act simultane-
™
to your MIDI device's MIDI IN.
ously as a pedal switcher. To utilize this function, the BluGuitar
LOOPERKIT
™
must be installed in the REMOTE1
™
are preassigned. Assigning the programms must therefore be done
This saves space on the pedalboard and allows for easier operation.
The LOOPERKIT
™
has four True-Bypass-Relay-Loops that you can add
your effect pedals to. When the LOOPERKIT
determine which of the four loops is active while programming your sound
presets, and store the information in the preset.
The LOOPERKIT
™
consists of an installation kit that has to be installed in
3
4
5
6
7
8
9
the REMOTE1
™
, and a Breakout-Box. The effect pedals that are to be
03
04
05
06
07
08
09
integrated into the set-up are connected to the Breakout-Box with short
12
13
14
15
16
17
18
patch cables. It has one input, one output and 4 of each send and return
21
22
23
24
25
26
27
jacks for the 4 loops.
30
31
32
33
34
35
36
In Direct-Access-Mode you determine which pedal(s) are activated for
each preset. Then you combine these specific effect pedal(s) with your
amp settings and store it as preset. Switching presets will recall amp
settings and turnes specific pedal(s) on or off, depending upon which
effects you have integrated in the presets, without having to activate
each effect singly per foot. Any pedals not being used are bypassed with
the True-Bypass-Relay. That keeps the signal path short by assuring that
it does not pass through every single pedal. Using high quality patch
cables results in an audibly better sound.
™
- PEDAL-SwITChER
Programming the Loops
®
To activate or deactivate loops, while in Direct-Access-Mode, press
™
.
and hold the FX-LOOP-Switch for about 2 seconds until it blinks.
Switches
1-4
will now show you which loops are active: if one of the
loops is active, the corresponding switch will be lit; if the switch is in
™
is installed, you can
bypass mode, the switch is unlit.
Activating a footswitch toggles between the loop is active (switch is lit)
or in bypass (switch is unlit). To store the activated setting, hold the
Mode/Store switch until all 9 switches are blinking. Pressing one of the
blinking pedals stores the current setting to this location.
Tip: sometimes it can be useful to connect several pedals one after
another in a loop if the effects are only to be used for a certain
sound or channel with the AMP1
™
. For example, I use various
modulation effects and a compressor for my clean sound only.
I activate the modulation effect pedal when needed using the
effect pedal bypass-switch.
Publicité
