BluGuitar REMOTE 1 Mode D'emploi page 18

FROM "STRAIGhT FORwARD AMP" TO AN INDIVIDUAL GUITAR SySTEM
A lot of new features, intuitive operating, compact and expandable.
REMOTE1 ™ is the optimal pedal controller (foot operated controller) for the BluGuitar ® AMP1 ™ . You can comfortably navigate through all the important AMP1
additional features. From choosing preset sounds to programming custom sounds, with the REMOTE1 ™ can do it all!
Midi-compatible devices can be connected to the MIDI Out connector and the REMOTE1 ™ presets can then be used to select the device's programs. And as if that wasn't enough!
If that wasn't enough, with the optional BluGuitar ® LOOPERKIT ™ you can integrate external effect pedals into your setup.
In short, with the help of the REMOTE1 ™ , you can turn your AMP1 ™ into a professional, programmable guitar system.
BluGuitar ® offers all the components - you decide how far you want to go!
Important Safety Notice! Read before connecting!
REMOTE1 ™ can only be connected to the AMP1 ™ 's REMOTE input. Use a stadard 6.3mm
(1/4inch) male to male, mono guitar or speaker cable. This product was manufactured
according to IEC 60065 and left the factory safety tested and ready for operation.
Further safety notices can be found in the AMP1 ™ user's guide.
Troubleshooting:
If the REMOTE1 ™ is not functioning correctly:
• make sure AMP1 ™ is not in PRESET MODE (see AMP1 ™ manual page 95)
• check the connection cable and replace if necessary
• disconnect the unit from the AMP1
™ , then reconnect
• factory reset: while pressing buttons 1, 6 and 7 simultaneously, power up the AMP1 ™ .
The REMOTE1 ™ will be reset to the factory default.
Note: this will delete all custom settings
™ functions by foot as well as accessing all the
PLUG AND PLAy! wITh ThE COMFORTABLE FOOTBOARD FOR ThE AMP1
Turn your AMP1 ™ into a 4 channel amp with additional functions like Direct-Access-Mode
2nd Master, PowerSoak,and programmable MIDI Out, that is also Direct-Access offers access to: Clean, Vintage, Classic, Modern,
programmable. Whether you use the REMOTE1 ™ as an old school Boost, Reverb, FX-Loop, 2nd Master Volume and PowerSoak.
Direct-Access is active when the Mode/Store switch is not lit.
footboard for stardard function switching, or to choose between
complex presets is totally up to you.
Connect the REMOTE1 ™ to the REMOTE-input on the AMP1 ™ using Preset-Mode
a standard Mono instrument cable. This cable transfers the control When the switch is pressed, it will light up and the Preset-Mode is
signal and supplies power to the REMOTE1 ™ . An additional power activated. Here you can save 36 presets in 4 banks of 9 presets each.
supply is unnecessary. When REMOTE1 is connected to AMP1
™ ™ , two Pressing the Mode/Store switch again puts you back in the Direct-
different modes are available using the Mode/Store switch. Access-Mode.
Speaker Out
FX-Loop
REMOTE1 ™
™ ThE PEDAL-SwITChER MAKES USING FX PEDALS EASy
Effect pedals have never been as popular as they are today. Trying to always turned on. In the switching board itself, loops can be activated or
get excellent sounds and intuitive operating can often only be acheived deactivated. If a loop is activated, the signal is sent through the the loop
using a combination of different, high-quality effect pedals, and as soon and the connected effect pedal(s). When not activated, the signal goes
directly through the Pedal-Switchers, by passing the effect pedals not
as multiple effects come into play, things start getting complicated and
switching sounds turns into a tapdance. in use (True-Bypass) to maintain signal strength. This minimizes second-
ary noise and loss of signal.
To solve this problem, so called Pedal-Switchers were developed. They
consist of a control center that coordinates and controls multiple effect The BluGuitar LOOPERKIT ™
®
loops. switcher with four True-Bypass-Loops. The combination of active pedals,
The effect pedals can be added to the different Pedal-Switchers loops and the AMP1 ™ 's sound settings can be saved as presets and accessed
singly or combined according to personal preference, your pedals are by the single press of a switch on the REMOTE1
Speaker Out
REMOTE1 ™
FX-Loop 1 2 3 4
Looper Kit
expands the REMOTE1 ™ to a pedal
™ .