Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
6
2.2
SPECIFICATIONS
SPECIFICATIONS
EN
FIREBOX CHAMBER
CAPACITY
APPROX. AREA HEATED**
MAXIMUM HEAT OUTPUT***
HEAT OUTPUT*
DURATION LOW FIRE*
WEIGHT w/o BRICKS
WEIGHT OF BRICKS
IDEAL WOOD LENGTH
(WHEN END LOADED)
* As tested using test method 28
** Figures will vary considerably with individual conditions.
*** Wolf Steel Ltd. estimated realistic BTU/hr with hardwood logs and regular refueling.
2.3
GENERAL INSTRUCTIONS
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH
LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN
ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN
THIS APPLIANCE HAS NOT BEEN TESTED WITH ANY VENTED OR UNVENTED GAS LOG SET. TO
REDUCE RISK OF FIRE OR PREVENT INJURY, DO NOT INSTALL A VENTED OR UNVENTED GAS LOG
BURNING YOUR UNIT WITH THE ASH DUMP DOOR OPEN OR AJAR CREATES A FIRE HAZARD THAT
MAY RESULT IN DISCOLOURATION TO THE GOLD PLATED DOOR, INTERNAL DAMAGE TO THE
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
THIS APPLIANCE AND IT'S COMPONENTS ARE DESIGNED TO BE INSTALLED AND OPERATED AS A
SYSTEM. ANY ALTERATION TO OR SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS ALLOWED
BY THESE INSTALLATION INSTRUCTIONS, WILL VOID THE LISTING AND MAY VOID THE PRODUCT
WARRANTY. IT MAY ALSO CREATE A HAZARDOUS INSTALLATION. READ THROUGH THESE
INSTRUCTIONS THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW THEM
•
Before beginning your installation, consult with your local building code agency or fire officials and
insurance representative to ensure compliance.
•
Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a
window near the appliance.
•
Remove any dust or debris off the top of the appliance before firing the appliance as the paint will
become soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your
appliance burn your appliance moderately hot during the first few fires.
•
To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door every
5-10 minutes.
•
For the first two weeks use generous amounts of fuel and burn the appliance with the damper wide
open for an hour as the appliance goes through a process of eliminating moisture in the firebricks. The
initial heat output will be reduced while the moisture is being drawn from the appliance and it will be
necessary to build several hot fires to remove this moisture. DURING THIS PROCESS DO NOT OVER
FIRE THE APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLIANCE IF THE
APPLIANCE OR CHIMNEY BECOMES RED.
W415-1476 / D / 08.21.18
S1
13 1/2"x18"x12"
(34.3cmx45.7cmx30.5cm)
1.7 ft
(0.05m
)
3
3
600-1500 ft
2
(56-139m
)
2
55,000 BTU/ Hr
11,700 - 42,200 BTU/ Hr
7 Hours
215 lbs (98kg)
110 lbs (50kg)
12" (30.5cm)
WARNING
!
THE UNITED STATES.
SET INTO THE APPLIANCE.
APPLIANCE OR A HOUSE CHIMNEY FIRE.
CAREFULLY THROUGHOUT YOUR PROJECT.
S4
18"x18"x12"
(45.7cmx45.7cmx30.5cm)
2.25 ft
(0.06m
)
3
3
1000-2000 ft
2
(93-186m
)
2
70,000 BTU/ Hr
11,400 - 41,300 BTU/ Hr
9 Hours
250 lbs (113.4kg)
145 lbs (65.8kg)
16" (40.6cm)
S9
22 1/2"x18"x12"
(57.2cmx45.7cmx30.5cm)
3.0 ft
(0.09m
)
3
3
1000-3500 ft
2
(93-325m
)
2
85,000 BTU/ Hr
11,800 - 34,000 BTU/ Hr
12 Hours
285 lbs (129kg)
114 lbs (52kg)
21" (53.3cm)
4.7
Publicité
Chapitres
Table des Matières
Dépannage
