Qualigen FastPack IP System Manuel page 68

Masquer les pouces Voir aussi pour FastPack IP System:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Troubleshooting the FastPack
Display  
"Unable to Read
Barcode"  
"Invalid Label"
"Unknown Test"  
"Restricted test type
due to temp"  
"Missing Pack"  
"Motor Failure"  
"PMT Background
High _ _ _"
"PMT Failure"  
"Shutter Failure"  
"Pressure Failure"  
"Remove FastPack"  
58                                                                                                                                                                                                                                                                                                                                                                                                                             6 5000159   R ev.   0 07   ( 06/15)  
IP System
®
Cause  
•   B ar   c ode   l abel   i s   i llegible.  
•   R eader   n on-­‐functional.  
•   W rong   t est-­‐type   p ack.  
•   C orrect   s oftware   v ersion   n ot   i nstalled.  
Operator   a ttempted   t o   r un   a   F astPack
test   t hat   i s   i ncompatible   w ith   t he  
temperature   o f   t he   a nalyzer.  
There   i s   n o   p ack   i n   t he   a nalyzer.  
Motor   h as   f ailed.  
PMT   b ackground   r eading   i s   h igh   d uring  
self-­‐diagnostic   o r   a t   b eginning   o f   a   t est.  
This   m ay   r esult   f rom   c ontamination,  
leakage   o f   a mbient   l ight   i n   t he   a nalyzer,  
or   a ttempting   t o   u se   a   p reviously   u sed  
FastPack®   I P.  
PMT   F ailure;   L ight   L eak.  
Shutter   F ailure  
System   h as   a   s evere   p ressure   l eak.   A ir  
pump   n ot   f unctioning.  
®
A   F astPack
  I P   i s   i n   t he   a nalyzer   w hen  
attempting   t o   r un   d iagnostics.  
Action  
•   C heck   t o   s ee   i f   b ar   c ode   i s   d efaced.  
•   R eposition   b arcode   l abel   a pprox.   ⅛ -­‐
inch   l ower   a nd   r e-­‐try.  
• If   P lexiglas   b arcode   w indow   i s   p resent,  
use   a   s tandard   f lat   h ead   s crewdriver   t o  
remove   t he   w indow   a nd   r e-­‐try.  
®
•   V erify   t hat   F astPack
  I P   a nd   C alibrator  
card   a re   o f   t he   s ame   t est-­‐type.  
•   C ontact   S ystem   S upport  
®
 
Attempt   t o   r un   t he   F astPack
analyzer   t hat   i s   t emperature   c ompatible.  
®
Insert   F astPack
  I P.  
Run   d iagnostic.   I f   i t   f ails,   c ontact   S ystem  
Support.  
Ensure   t hat   t he   u sed   F astPack
still   i n   t he   I nstrument.   E nsure   t hat   t he  
instrument   i s   n ot   i n   d irect   s unlight.  
Follow   c leaning   p rocedure.   R un   s elf-­‐
diagnostic.   C ontact   S ystem   S upport   i f  
message   p ersists.  
Ensure   t hat   t he   a nalyzer   i s   n ot   i n   d irect  
sunlight.   C ontact   S ystem   S upport.  
Contact   S ystem   S upport.  
Contact   S ystem   S upport.  
®
Remove   F astPack
  I P.   U pon   c losing   d oor,  
diagnostics   w ill   a utomatically   b egin.  
®
  o n   a n  
®
  I P   i s   n ot  

Publicité

Table des Matières
loading

Table des Matières