Publicité
Les langues disponibles
Les langues disponibles
maximum safety, so the least amount of
wheel is exposed towards the operator.
The guard helps to protect the operator from
broken wheel fragments, accidental contact
with wheel and sparks that could ignite
clothing.
d) Wheels must be used only for
recommended applications. For example:
do not grind with the side of cut-off
wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
e) Always use undamaged wheel flanges
that are of correct size and shape for
your selected wheel. Proper wheel flanges
support the wheel thus reducing the possibility
of wheel breakage. Flanges for cut-off wheels
may be different from grinding wheel flanges.
f)
Do not use worn down wheels from
larger power tools. Wheels intended for
larger power tools is not suitable for the higher
speed of a smaller tool and may burst.
ADDITIONAL SAFETY
INSTRUCTIONS FOR
CUTTING-OFF OPERATIONS
Additional Safety Warnings Specific for
Abrasive Cutting-Off Operations:
a) Do not "jam" the cut-off wheel or apply
6
excessive pressure. Do not attempt
to make an excessive depth of cut.
Overstressing the wheel increases the loading
and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback
or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your body, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when
interrupting a cut for any reason, switch
off the power tool and hold the power
tool motionless until the wheel comes
to a complete stop. Never attempt to
remove the cut-off wheel from the cut
while the wheel is in motion otherwise
kickback may occur. Investigate and take
corrective action to eliminate the cause of
wheel binding.
d) Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully reenter the cut. The
wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
e) Support panels or any oversized
workpiece to minimize the risk of wheel
pinching and kickback. Large workpieces
tend to sag under their own weight. Supports
must be placed under the workpiece near the
20V Cordless Brushless Angle Grinder EN
line of cut and near the edge of the workpiece
on both sides of the wheel.
f)
Use extra caution when making a "pocket
cut" into existing walls or other blind
areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred battery
pack.
b) Do not expose battery pack to heat or
fire. Avoid storage in direct sunlight.
c) Do not short-circuit a battery pack. Do
not store battery packs haphazardly in a
box or drawer where they may
short-circuit each other or be
short-circuited by other metal objects.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or fire.
d) Do not remove battery pack from its
original packaging until required for use.
e) Do not subject battery pack to
mechanical shock.
f)
In the event of battery leaking, do not
allow the liquid to come in contact with
the skin or eyes. If contact has been
made, wash the affected area with
copious amounts of water and seek
medical advice.
g) Observe the plus (+) and minus (–) marks
on the battery back and equipment and
ensure correct use.
h) Do not use any battery pack which is not
designed for use with the equipment.
i)
Keep battery pack out of the reach of
children.
j)
Seek medical advice immediately if a cell
or battery has been swallowed.
k) Always purchase the battery
pack recommended by the device
manufacturer for the equipment.
l)
Keep battery pack clean and dry.
m) Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
n) Battery packs need to be charged before
use. Always use the correct charger and
refer to the manufacturer's instructions
or equipment manual for proper charging
instructions.
o) Do not leave battery pack on prolonged
charge when not in use.
p) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
Publicité
