Channel 10 Program Change/Channel Event Receive; Receive Program Change/System; Exclusive Messages - Yamaha DTXPRESS II Mode D'emploi

2. Select the type of bulk data (that will be sent) in the dis-
play shown above and press the [SAVE/ENT] button.
The display shown below will appear.
BULK all data
Are you sure ?
3. Press the [SAVE/ENT] or [VALUE+] button, the bulk dump
will be carried out.
* Press [VALUE-] to cancel the bulk dump.
When the operation is complete, the LCD will display "Com-
plete" as shown below.
BULK sssssssssss
Complete !
* The device number must be set for bulk dumps [3-6. Device
Number, Local Control] (P. 32)
* Refer to the [MIDI Data Format] section (P. 50) for more infor-
mation on bulk dump operations.
Receiving Bulk Data
DTXPRESS II data stored in an external device can be sent
back to the DTXPRESS II's MIDI IN/TO HOST jack using
Bulk Data Receive.
1. After reading the [Connecting a MIDI Device] (Basic
Guide : P. 12) or the [Connecting a Computer] (Ba-
sic Guide : P. 26) section, connect the MIDI device
or computer to the MIDI OUT jack/TO HOST jack on
the DTXPRESS II. Set the HOST SELECT switch.
2. With the sequencer (song, metronome) stopped,
send bulk data from the external device.
3. When the DTXPRESS II starts receiving data, the
following screen will appear on the LCD.
BULK Receiving
Please wait...
4. When the DTXPRESS II has completed receiving
all the data, the following screen will appear on the
LCD for a few seconds, then the screen will return to
the original display (before receiving bulk data).
BULK Receiving
BULK Received.
* Before receiving bulk data, it is necessary to match the de-
vice numbers (P. 32 [3-6]) of the DTXPRESS II and the
external device. It is also necessary to enable the
DTXPRESS II to receive exclusive messages (P. 31 [3-3]).

3-2. Channel 10 Program Change/Channel Event Receive

This enables or disables the DTXPRESS II to receive program
change messages/channel events through MIDI channel 10. Pro-
gram change messages received or transmitted through channel
10 can be used to switch DTXPRESS II drum kits.
It is necessary to set the receive parameter to "on" in this display
in order to switch the DTXPRESS II's drum kits from a song or an
external MIDI device.
UT MIDI RECEIVE
10PC= on 10= on
q
q 10PC (Receive Program Change)
This enables or disables the DTXPRESS II to receive program
change messages through MIDI channel 10.
off: Does not receive.
on: Receives.
* Even if the q 10PC parameter is set to "on", program change
messages from MIDI channel 10 will not be received in the fol-
lowing cases.
• If the w 10 (receive channel event) parameter is set to "off"
• If the [3-3. Receive Program Change/System Exclusive
Message's] q PC (program change) parameter is set to "off".
w 10 (Receive Channel Event)
This enables or disables the DTXPRESS II to receive MIDI chan-
nel messages through MIDI channel 10.
off: Does not receive.
on: Receives.

3-3. Receive Program Change/System

Exclusive Messages

This enables or disables the DTXPRESS II to receive program
change messages/system exclusive messages from all MIDI chan-
nels.
UT MIDI RECEIVE
PC= on SySEx= on
q
q PC (Receive Program Change)
off: Does not receive program change messages.
on: Receives program change messages.
w SySex (Receive System Exclusive Messages)
off: Does not receive system exclusive messages.
on: Receives system exclusive messages.
Utility Mode
w
w
31