Introduction; Layout; Scope Of Delivery; Proper Use - Scheppach GK240of Traduction Des Instructions D'origine

1. Introduction

Manufacturer
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were in-
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety notices contained in this
operating manual and the particular instructions for
your country, the generally recognised technical reg-
ulations for the operation of identical devices must
be complied with.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
2. Layout (Fig. 1 - 5)
1. Transport handle
2. Quick-coupling
3. Pressure regulator
4. Manometer
5. Safety Valve
6. ON/OFF switch
7. Pressure vessel
8. Wheel
9. Air filter
10. Supporting foot
11. Drain plug for condensation water

3. Scope of delivery

m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
• 1x Screw (Supporting foot)
• 1x Nut (Supporting foot)
• 1x Flat Washer (Supporting foot)
• 1x Spring Washer (Supporting foot)
• 2x Nut (Wheels)
• 2x Spring Washer (Wheels)
• 2x Flat Washer (Wheels)
• 2x Screw (Wheels)
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.

4. Proper use

The compressor is designed to generate compressed
air for compressed-air driven tools which can be driv-
en with an air volume of up to approx. 120 l/min (e.g.
tire inflator, blow-out pistol and paint spray gun).
Due to the restricted air flow rate, it is only possible
to operate tools with a very high compressed air con-
sumption (e.g. orbital sanders, straight grinders and
impact screwdriver) in some circumstances.
The compressor may only be operated in a dry and
well ventilated indoor space.