Introduction - golmar Stadio Plus T500SE ML Manuel D'installation

INTRODUCTION

First of all we would like to thank and congratulate you for the purchase of this product manufactured by
Golmar.
The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification
and for the manufacturing of products like this one.
Its advanced technology and exacting quality control will do that customers and users enjoy with the
legion of features this system offers. To obtain the maximum profit of these features and a properly wired
installation, we kindly recommend you to expend a few minutes of your time to read this manual.
INDEX
Introduction......................................101
Index ...............................................101
Starting recommendations..................101
Safety precautions .............................102
System characteristics ..............102 to 103
System operation...............................103
Door panel installation.............................
Description ....................................104
Embedding box positioning ....105 to 106
Door panel modules assembly ..........106
Electronic modules assembly ............107
Door panel fixing ............................108
Place informative window label .........108
Push buttons wiring................109 to 110
Push buttons coding ........................111
EL500SE configuration ............112 to 113
Programming (general panel) .114 to 116
Informative window connection.........116
Lamps wiring ..................................117
Final adjustments ............................117
Power supply installation.....................118
Lock release installation .....................118
Platea Plus monitor ..................................
Description ....................................119
Function push buttons......................120
EL562 module................................121
STARTING RECOMMENDATIONS
Do not use excessive force when tightening the power supply connector screws.
The entire installation must be at least 40cm. away from any other installation.
Before to connect the system, check the connections between door panel, monitors, telephones, and
the transformer connection. Do always follow the enclosed information.
Each time the power supply is restarted, or after a modification, the system will remain blocked during
30 seconds.
Always use RG-59 B/U MIL C-17 or RG-11 coaxial cables, (see page 134). Never use coaxial
antenna cable. In installations no longers than 100m., Golmar RAP-5130 cable can be used.
101
End of line resistor ...........................121
Front film replacement .....................121
Monitor connector description ..........122
Monitor installation .........................123
Programming .................................124
T-940 Plus telephone ...............................
Description ....................................125
Function push buttons......................125
Telephone installation......................126
Programming .................................127
T-740 Plus telephone ...............................
Description ..........................128 to 129
Function push buttons......................129
Telephone installation......................130
Programming .................................131
Installation diagrams ...............................
Connection of an a.c. lock release.....132
Link of several power supplies ...........132
Video installation with coaxial.......133-134
Video installation without coaxial ..135-136
Audio installation.......................137-138
Video installation (general panel) ..139-142
Audio installation (general panel) ..143-144
Optional connections ...................145-148
Troubleshooting hints.........................149
Compliance .....................................151
102
Install or modify the equipment without the power connected.
The installation and handling of these equipments must be performed by authorised personnel.
The entire installation must be at least 40 cm. away from any other installation.
With power supply:
Do not use excessive force when tightening the connector screws.
Install the power supply in a dry and protected place without risk of drip or water projections.
Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
Do not block ventilation holes of the unit so that air can circulate freely.
To avoid damage, the power supply has to be firmly fixed.
To avoid an electrical shock, neither remove the protection cover nor handle the connected wire in
the terminals.
With monitor, telephones and distributor:
Do not use excessive force when tightening the connector screws.
Install the power supply in a dry and protected place without risk of drip or water projections.
Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
Do not block ventilation holes of the equipments so that air can circulate freely.
Remember, the installation and handling of these equipments must be performed by authorized
personnel and in the absence of electrical current.
Do always follow the enclosed information.
Microprocessed system with simplified installation:
Audio door entry system with 4 common wires installation.
Video door entry system with 3 common wires plus coaxial cable installation.
Video door entry system with 4 common wires plus twisted pair installation.
Microprocessed circuit EL500SE with two operating modes(EL500 or EL501).
Unlimited number of door panels (access) being not necessary the use of switching units.
Up to 120 monitors/telephones per installation or backbone.
General door panel (EL501 mode): Up to 120 monitors/telephones, distributed in max. 120 buildings.
EL560 module for video installations with twisted pair cable, integrated in EL500SE circuit.
Communications resistor for the system UNO or PLUS, integrated in EL500SE circuit.
Acoustic busy channel and call acknowledgement signals.
Door opening timed at 3 seconds.
Input for external door release push button (timed at 3 or 15 seconds).
a.c or d.c lock release operated by relay.
Up to three monitors or telephones in the same apartment without additional power supplies.
With T-940 Plus telephones:
Privacy on audio communications.
Three-position control for call volume: maximum, medium and minimum.
Intercommunication function with other monitor or telephone of the same apartment.
Input for external door bell push button.
Output for additional call repeater.
Call to a master porter's exchange.
Panic call to the porter's exchange.
Different call reception tones depending where the call is comming from: main or slave door
panels, door bell push button, intercom, ...
With T-740 Plus telephones, addition to the above features:
Three-position control for call volume: maximum, medium and off.
Input for external door release push button.
SAFETY PRECAUTIONS
SYSTEM CHARACTERISTICS
Continue