Device Description (Fig. 1 - 2); Scope Of Delivery - Scheppach WSE3200 Traduction Des Instructions D'origine

Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were in-
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety requirements in these operat-
ing instructions and your country's applicable regula-
tions, you should observe the generally recognized
technical rules concerning the operation of welding
machines.
14 | GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Device description (fig. 1 - 2)

1. Burner nozzle
2. Burner button
3. Burner
4. Hose assembly with direct connection
5. Earth cable with earth clamp
6. Locking mechanism
7. Carry strap (already attached)
8. Cover for wire feeding device
9. Combination wire brush with slag hammer
10. Cored-wire roll
11. Contact tip
12. Switch for setting the welding current
13. On/off switch
14. Overload protection indicator lamp
15. Adjusting wheel for wire feed (potentiometer)
16. Welding mask
17. Plastic frame
18. Knurled screws + nuts
19. Handle
20. Ancillary glass
21. Protective glass for the welding mask

Scope of delivery

1. Welding machine
2. Hose assembly, complete
3. Earthing clamp, complete
4. Carrying strap
5. Combination wire brush
6. Cored-wire roll
7. Welding mask, complete
8. Operating manual
Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swallow-
ing and suffocation!
Important information
Please read the directions for use carefully and ob-
serve the information provided. It is important to con-
sult these instructions in order to acquaint yourself
with the machine, its proper use and safety precau-
tions.