EINHELL TC-SB 305 U Mode D'emploi D'origine page 27

6.4.3. Adjusting the upper guide pins (28)
•
Undo the Socket head screw (35)
•
Move the mount (36) of the guide pins (28) so
that there is a gap of approx. 1 mm between
the front edge of the guide pins (28) and the
gullet of the blade in front.
•
Re-tighten the Socket head screw (35).
•
CAUTION! The blade will be rendered usel-
ess if the teeth touch the guide pins while the
blade is running.
•
Undo the Socket head screws (37).
•
Move the guide pins (28) towards the blade
so that there is a gap of approx. 0.5 mm bet-
ween the guide pins (28) and the blade (26).
The blade must not jam.
•
Re-tighten the Socket head screws (37).
•
Turn the upper blade pulley (8) several times
in a clockwise direction.
•
Check the setting of the guide pins (28) again
and re-adjust if necessary.
6.4.4. Adjusting the lower guide pins (29)
•
Dismantle the saw table (15).
•
Undo the screw (48).
•
Move the mount (32) of the guide pins (29) so
that there is a gap of approx. 1 mm between
the front edge of the guide pins (29) and the
gullet of the blade in front.
•
Re-tighten the screw (40).
•
CAUTION! The blade will be rendered usel-
ess if the teeth touch the guide pins while the
blade is running.
•
Undo the screws (38).
•
Move the guide pins (29) towards the blade
so that there is a gap of approx. 0.5 mm bet-
ween the guide pins (29) and the blade (26).
The blade must not jam.
•
Re-tighten the Socket head screws (38).
•
Turn the lower blade pulley (7) several times
in a clockwise direction.
•
Check the setting of the guide pins (29) again
and re-adjust if necessary.
CAUTION! When the adjustments have been
fi nished, the blade guard (34) must be closed
again.
6.5.1 Adjusting the upper blade guide (11)
(Figure 2, 9)
•
Undo the fixing handle (20).
•
Turn the setting wheel (19) to lower the blade
guide (11) as close as possible to the workpi-
ece to be cut. The gap should be approx. 2-3
mm.
•
Re-tighten the fixing handle (20).
GB
•
6.5.2 Adjusting the blade speed (Fig. 10, 11)
The bandsaw can be operated at two blade
speeds.
To change the position proceed as follows:
•
•
•
6.6 Adjusting the machine table (15) to 90°
•
•
•
•
•
•
•
•
Important: Never use warped or lacerated
blades!
6.7 Changing the blade (Fig. 14)
•
•
•
•
•
•
•
•
•
www.sidirika-nikolaidi.gr
- 27 -
Check the setting before each cut and re-
adjust if necessary.
Slacken the drive belt (A) by turning the hand
wheel (43) in an anticlockwise direction.
Move the belt to the desired position on the
belt pulley (B) and the lower blade pulley (7).
Tension the drive belt (A) again by turning the
hand wheel (43) in a clockwise direction.
Important: Drive belts must not be tensioned
too much.
(12/13)
Move the upper blade guide (11) to the top.
Undo the fixing handles (18).
Place the angle (d) between the blade (26)
and the table (15). The angle (d) is not inclu-
ded in delivery.
Turn the setting wheel (19) to tilt the saw table
(15) until it is at an angle of exactly 90° to the
blade (26).
Re-tighten the fixing handle (18).
Undo the nut (49).
Adjust the Socket head screw (50) until there
is contact with the machine frame.
Re-tighten the nut to fasten the Socket head
screw.
Move the blade guide (11) into a position
approximately half way between the saw table
(15) and the machine housing (25).
Undo the fasteners (13) and open the side
cover (12).
Remove the bolt (4)
Turn the tightening screw (9) anti-clockwise to
remove the tension from the blade (26).
Remove the blade (26) from the blade pulleys
(7, 8) and take out through the slot in the table
(15).
Fit the new blade (26), aligned centrally on
the blade pulleys (7, 8). The teeth of the blade
(26) must point downwards in the direction of
the table.
Tension the blade (26) (see 6.2)
Close the side cover (12) again.
Refit the bolt (4)