Device Description; Multitool Safety Warnings; Additional Safety And Working Instructions; Specified Conditions Of Use - Milwaukee M18 FMT Notice Originale

2
1

Device description

1
LED
2
Quick release lever
3
On/O switch
4
Battery
5
Speed dial
6
Inner ange
7
Adapter
8
Accessory bolt
WARNING
Read all safety warnings, instructions, illustrations and
speci cations provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, re and/
or serious injury.
Save all warnings and instructions for future reference.

MULTITOOL SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a „live"
wire may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the workpiece by
hand or against your body leaves it unstable and may lead to loss
of control.

Additional Safety and Working Instructions

Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device o immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
4
3
5
6
7
8
Possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING
Danger of burns!
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpi-
eces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft mate-
rials (wood, light building materials for walls). Harder materials
(metals) must rst be drilled with a hole corresponding to the size
of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors o er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it o immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your device, battery
pack or charger in uid or allow a uid to ow inside them.
Corrosive or conductive uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.

SPECIFIED CONDITIONS OF USE

The Maschine can be combined with di erent tools and is designed
for following use:
Sander Head: sanding wood, metal and plastics
Segment saw blade head: for cutting ush to a surface in wood
and plastics.
Universal blade head: for working in wood.
Do not use this product in any other way as stated for normal use.
GB
English
15