Campingaz Fargo TwinPack Utilisation Et Entretien page 10

3. If the burner fails to light, turn the control knob "a" to
the "off" position (O). Wait 5 minutes before repeating
the operation.
GB
Important:
If the burner fails to light after the 2 nd attempt, turn the
control knob "a" to the "OFF" position (O) and check that
the burner outlets and the venturi tube are not blocked.
burner outlets
D-3 Manual burner ignition
If Piezo ignition does not work, put the "a" adjustment
lever in the "OFF" (O) position. Remove the drippings
tray located under the vat. Hold a lighted match to the
opening located under the burner, then open the "a"
lever on the control panel to full-flow position ( ).
Reposition the drippings tray.
E - TURNING OFF THE DEVICE
1. Turn the "a" adjustment lever to the "OFF" (O) position.
2. Close the TwinPack regulator valve by turning the "b"
knob in a clockwise direction.
F - OPERATION
1. It's recommended that protective gloves be worn to
handle components which may be very hot.
2. Before start-up, put the feet in place, then open the fold-
down shelves (see paragraph B).
3. Never turn your Fargo
the shelves in a closed position.
4. Do not put a weight of more than 2 kg on the
shelves when they are in the open position.
5. Before cooking, preheat the device for a few minutes in
the full flow position ( ).
Important :
If a burner flame goes out
when the unit is in use,
immediately turn
control knob to the "off" (O)
position.
G - REMOVING A CV 470 PLUS CARTRIDGE
The cartridge may be removed even if it is not empty.
Replace the cartridge outside and away from other
people.
- Check that gas input is properly closed by turning the
"a" adjustment lever to the OFF position (O) and by
turning the TwinPack "b" in a clockwise direction until it
stops.
- Be sure that the burner is turned off before removing the
cylinder.
- Holding the TwinPack, unscrew the cylinder by turning it
in a counter-clockwise direction and remove it.
- Repeat these steps for the second cylinder if necessary.
burner tube
TM TwinPack on with
the
Never throw away a cartridge which is not completely
empty, (check there is no liquid in the cartridge by
shaking it).
H - PRECAUTIONS FOR USE
Never use your device less than 60 cm from a
wall or combustible object.
Avoid twisting the flexible hose.
Do not operate the device using only one
cylinder.
Do not operate the device when one of the
two cylinders is empty. You risk not being
able to obtain the power necessary for proper
operation.
Check the sealing rings before assembling a
new gas recipient.
After use, first close the "b" valve on the
TwinPack; when the flame goes out, close the
"a" valve on the device.
I - CLEANING AND MAINTENANCE
- Never modify the barbecue: any modification may prove
dangerous.
- In order to maintain your barbecue in perfect operating
condition, it is recommended to clean it periodically (after
4 or 5 uses).
- Turn your device off (see paragraph E - TURNING OFF
THE DEVICE.
- Wait until the barbecue has cooled down before
cleaning.
- If not used during more than 30 days the grill burner
must be cleaned and checked.
- Clean the top of the burner, as well as the sides and
base, using a moist sponge (water with washing up
liquid). If necessary, use a damp steel brush.
- Check that all burner outlets are clear and let dry before
using again. If necessary, use a wire brush to unclog the
burner outlets.
N.B.: Frequent cleaning of the burner maintains it in good
condition for many uses and prevents premature
oxidation, notably due to acid residue from cooking.
Oxidation of the grill burner is, however, normal.
Stove sides, fold-down shelves, control panel,
drippings tray
Clean these elements from time to time using a sponge
with washing up liquid. Do not use abrasive products.
Cooking grill
The cooking grill is covered with enamel. To clean it, we
recommend first removing all cooking residues with a
sponge or scouring pad. Next, remove grease with a
dishwashing detergent or by putting the cooking grill in
your dishwasher.
Be careful to avoid hitting the cooking grill against a hard
surface since this could chip the enamel.
10