Publicité
Les langues disponibles
Les langues disponibles
4
Remote control programming.
How to program the remote controls to the function START:
1) Press and release button SET; led DL3 starts flashing slowly
2) Press the remote control button; led DL3 will turn on for 2 seconds to confirm the code has been memorized.
How to program the remote controls to the function PEDESTRIAN (partial opening):
1) Press and release button SET twice; led DL3 starts flashing slowly
2) Press the remote control button; led DL3 will turn on for 2 seconds to confirm the code has been memorized.
You can store up to 32 different codes in the onboard receiver (16 Start + 16 Ped). If you overpass this limit, while storing the
remote control code, led DL3 will flash fast twice and will turn off without accepting any other code.
We recommend to store the remote controls into the control panel receiver with the antenna NOT wired.
5
Remote controls erasing.
How to erase only one code related to the START or to the PEDESTRIAN:
1) Press and release at the same time button SET and BREAK, led DL3 will flash quickly.
2) You have approx. 10 sec. to press the remote control button where you have stored the code you desire to erase. When code is
erased, led DL3 flashes for 1 sec. and then turns off (cancellation confirmed).
How to erase all the remote controls stored in the control panel memory:
1) Keep pressed at the same time button SET and BREAK for approx. 10 seconds.
Led DL3 will flash slowly and after 10 seconds will turn off.
6
Preliminary checks before programming the operator.
1) Cut off main power supply, wait 3 seconds and give power back.
2) Check that led Stop, Costa, Foto and f.ap. are lighted up.
3) Manually release the operator and open the gate till the end in order to verify that led f.ap turns off (if it does not tu rn off, move
the magnet on the bracket towards the operator (sensor); if instead led f.ch turns off, then turn the other way round the magnet in
the bracket).
4) Now, close the gate till the end position in order to verify that led f.ch turns off (if it does not turn off, move the ma gnet on the
bracket towards the operator (sensor); if instead led f.ap turns off, then turn the other way round the magnet in the bracket .
5) Place the gate now in the half way position and re-establish the automatic working by closing the releasing handle. Give a Sta rt
with the r emote control, gate should open as first movement. If it doesn't happen, cut off main power supply, invert wires 6 with 7
and give power again.
7
Gate movement programming.
Simple gate movement programming:
1) Close the gate completely (led f.ch turns off) and keep pressed button SET (led DL3 starts flashing) until the gate starts opening.
The gate will reach the limit switch opening and led DL3 will turn off. After 1 second the gate starts closing until it will reach the limit
switch closing keeping a fix slowing down space of approx. 20 cm. At the end of the auto -programming the control panel goes out
from the programming on its own. With this type of programming you will get a fix slowing down space both in opening and clos ing
of approx. 20cm.
Customised gate movement programming:
1) Close the gate completely (led f.ch turns off) and press once button SET (led DL3 starts flashing slowly).
2) Press now button WORK. The gate starts opening.
3) As soon as the gate has reached the desired position when you want to set the slowing down in opening, press again WORK; the
gate will continue in a slow motion until it reaches the limit switch opening (led DL3 turns off) and it stops.
4) After 2 seconds the gate re-closes at normal speed slowing down before reaching the limit switch of closing, led DL3 turns off.
The control panel has memorised the customised slowing down space.
The slowing down space memorised in the opening will be automatically kept also in the closing movement.
NOTICE: if you want to modify the slowing down spaces you have to repeat the "Customised programming" in order to program
over the previous programming new spaces. There is not a way to re-program just the slowing down spaces.
Publicité
