Hitachi DS 14DFL Instructions De Sécurité Et Mode D'emploi page 18

English
●
When a large force is required for operation
(operations indicated in the following chart) set
the shift knob to "LOW". If "HIGH" is set and the
unit is used, it may cause the motor to burn out
or malfunction prematurely.
Model
Metal Drilling
Wood Drilling
Wood Screw
Tightening
7. Confirm the clutch dial position (See Fig. 18).
The tightening torque of this unit can be adjusted
according to the clutch dial position, at which the
clutch dial is set.
Weak
Strong
(1) When using this unit as a screwdriver, line up the
one of the numbers "1, 3, 5 ... 22" on the clutch
dial, or the black dot, with the triangle mark on the
outer body.
(2) When using this unit as a drill, line up the clutch
dial drill mark "
outer body.
CAUTION:
●
The clutch dial cannot be set between the numbers
"1, 3, 5 ... 22" or the black dot.
●
Do not use with the clutch dial set at the line
between the number "22" and the drill mark
" ". Doing so may cause damage (See Fig. 19).
mark
Line
18
DS14DFL
When the diameter of the hole
exceeds 1/4 in. (6.5 mm).
When the diameter of the hole
exceeds 15/32 in. (12 mm).
When the size of the wood
screw exceeds 5/32 in. (3.8 mm)
diameter × 1-31/32 in. (50 mm).
Clutch dial
Triangle mark
mark
Fig. 18
" with the triangle mark on the
Triangle mark
Fig. 19
Table 5
When the diameter of the hole
exceeds 5/16 in. (8 mm).
When the diameter of the hole
exceeds 15/16 in. (24 mm).
When the size of the wood
screw exceeds 3/16 in. (4.8 mm)
diameter × 1-9/16 in. (40 mm).
8. Tightening torque adjustment.
(1) Tightening torque
Tightening torque should correspond in its
intensity to the screw diameter. When too strong
power is used, the screw head may be broken or
be injured.
Be sure to adjust the clutch dial position according
to the screw diameter.
(2) Tightening torque indication (See Fig. 18)
The tightening torque differs depending on the
type of screw and the material being tightened.
The unit indicates the tightening torque with the
numbers "1, 3, 5 ... 22" on the clutch dial, and a
dot. The tightening torque at position "1" is the
weakest and the torque is strongest at the highest
number.
(3) Adjusting the tightening torque (See Fig. 18)
Rotate the clutch dial and line up the numbers "1,
3, 5, ... 22" on the clutch dial, or the dot, with the
triangle mark on the outer body. Adjust the clutch
dial in the weak or the strong torque direction
according to the torque you need.
CAUTION:
●
The motor rotation may be locked to cease while
the unit is used as drill. While operating the driver
drill, take care not to lock the motor.
●
When setting the shift knob to "HIGH" (high
speed) and the position of the clutch dial is "17"
to "22", it may happen that the clutch does not
engaged and that the motor is locked. In such a
case, please set the shift knob to "LOW" (low
speed).
●
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor or
battery may be burnt.
●
Too long hammering may cause the screw broken
due to excessive tightening.
●
A buzzing noise is produced when the motor is
about to rotate; This is only a noise, not a machine
failure.
DS18DFL