Motor Brushes; Lubrication - DeWalt D25032 Traduction De La Notice D'instructions Originale

7. When drilling through a structure thicker than the depth of
the core bit, break away the round cylinder of concrete or
core inside the bit at regular intervals. To avoid unwanted
breaking away of concrete around the hole, first drill a hole
the diameter of the center drill completely through the
structure. Then drill the cored hole halfway from each side.
8. Always switch off the tool when work is finished and
before unplugging.
Rotary Drilling (Fig. A)
1. Hold down the mode selector button
selector switch 4 to the "rotary drilling" position.
2. Depending on your tool, follow either of the following
instructions:
D25032, D25033, D25133, D25143, D25263: Fit the
-
chuck adapter/chuck assembly.
- D25134, D25144: Replace the
SDS Plus tool holder with the keyless chuck.
3. Proceed as described for hammerdrilling.

WARNING: Never use standard chucks in the
hammerdrilling mode.
Screwdriving (Fig. A)
1. Hold down the mode selector button
selector switch 4 to the rotary drilling position.
2. Select the direction of rotation.
3. Depending on your tool, follow either of the following
instructions:
D25032, D25033, D25133, D25143, D25263: Insert
-
the special SDS Plus screwdriving adaptor for use with
hexagonal screwdriver bits.
- D25134, D25144: Replace the SDS Plus tool holder
with the keyless chuck
4. Insert the appropriate screwdriver bit. When driving slotted
head screws always use bits with a finder sleeve.
5. Gently press the variable speed switch
damage to the screw head. In reverse (LH) rotation the tool
speed is automatically reduced for easy screw removal.
6. When the screw is flush with the workpiece, release the
variable speed switch to prevent the screw head from
penetrating into the workpiece.
Chipping and Chiselling (Fig. A)
D25033, D25133, D25134, D25143,
D25144, D25263
1. Hold down the mode selector button
selector switch 4 to the "hammering only" position.
2. Insert the appropriate chisel and rotate it by hand to lock it
into position.
3. Adjust the side handle 8 as required.
4. Switch on the tool and start working.
5. Always switch off the tool when work is finished and
before unplugging.

MAINTENANCE
Your D
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
5 then set the mode
care and regular cleaning.

•
•
5 then set the mode

Motor Brushes

D WALT uses an advanced brush system which automatically
e
stops the drill when the brushes wear out. This prevents serious
damage to the motor. New brush assemblies are available
at authorised D
replacement parts.

Lubrication

Your power tool requires no additional lubrication.
Accessories and attachments used must be regularly lubricated
around the SDS Plus fitment.
1 to prevent
Cleaning


5 then set the mode
WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir in flammable liquids
labelled accordingly.
WALT power tool has been designed to operate
e
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
This machine is not user-serviceable. Take the tool to an
authorised D WALT repair agent after approximately 40
e
hours of use. If problems occur before this time contact an
authorised D WALT repair agent.
e
The tool will automatically switch off when the carbon
brushes are worn.
WALT service centers. Always use identical
e
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
EngLIsh
27