Technical Data; Noise/Vibration Information; Battery Charging - Bosch EasySaw 18V-70 Notice Originale

Technical data

Jigsaw
Article number
Stroke rate control
Rated voltage
No-load stroke rate n₀
Stroke
Max. cutting depth
– in wood
– in aluminium
– in steel (unalloyed)
Max. cutting angle (left/right)
Weight according to EPTA-Pro-
A)
cedure 01:2014
Recommended ambient temper-
ature during charging
Permitted ambient temperature
during operation B) and during
storage
Recommended rechargeable bat-
teries
Recommended battery char-
gers C)
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV

Noise/Vibration Information

Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 82 dB(A); sound power level
93 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑11:
Cutting boards with saw blade T 144 D:
2 2
a = 8.5 m/s , K = 2.5 m/s ,
h,B
cutting sheet metal with saw blade T 118 A:
= 10 m/s 2 , K = 2 m/s 2
a .
h,M
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
Bosch Power Tools
increase the vibration and noise emissions over the total
working period.
EasySaw 18V-70
To estimate vibration and noise emissions accurately, the
3 603 K12 0..
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
●
This may significantly reduce vibration and noise emissions
V= 18
over the total working period.
−1
min 2600
Implement additional safety measures to protect the oper-
mm 20
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
mm 70
mm 15
Assembly
mm 6
Remove the battery from the power tool before carry-
u
° 45
ing out work on the power tool (e.g. maintenance,
kg 1.7 (1.5 Ah)–
changing tool, etc.). The battery should also be re-
2.0 (6 Ah)
moved for transport and storage. There is risk of injury
°C 0 to +35
from unintentionally pressing the on/off switch.

Battery Charging

°C –20 to +50
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
PBA 18V...W-.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
AL 18...
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (4), press the release button (5) and
pull the battery upwards and out of the power tool. Do not
use force to do this.
Battery charge indicator
The battery charge indicator (3) indicates the charge condi-
tion of the battery when the power tool is switched on. It
consists of three green LEDs.
LEDs
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × slowly flashing green light
The three LEDs in the battery charge indicator (3) flash
quickly when the temperature of the battery is outside the
operating temperature range of −20 to +50 °C and/or the
overload protection has been triggered.
English | 17
Capacity
66–100 %
33–66 %
11–33 %
0–10 %
1 609 92A 64Y | (12.07.2021)