JVC D-ILA DLA-G20U Mode D'emploi page 46

Operating the Main Menu (Cont.)
Setting and Adjusting Other Functions (OPTIONS) (Cont.)
Remote control unit
OPERATE
COMPUTER VIDEO
T
VOL. ZOOM FOCUS
W
MENU/ENTER
PAGE
BACK
PRESET
QUICK AV
ALIGN. MUTING
PAGE BACK button
Submenu items
[OPTIONS menu]
O P T I O N S
M E N U A U T O O F F
L I N E D I S P L A Y
R I G H T L E F T R E V .
T O P B O T T O M I N V .
C L A M P
R E S I Z E
B A C K C O L O R
C O L O R T E M P .
A S P E C T C H A N G E
S L E E P T I M E
L A M P T I M E
Notes
• The selected item is shown in magenta color. Items shown
in gray color cannot be operated or set in the current mode.
• Items to be set (adjusted) are different when AV signals are
input and when computer-system signals are input.
• When you turn the RESIZE function ON, allowing the screen
to be enlarged virtually to its full size for projection (resizing
display), the video image (resolution) becomes coarse.
5
MENU/ENTER
button
Cursor buttons
N O
O N
O F F
O F F
B P
O N
B L U E
M I D D L E
4 : 3
3 0 M i n .
1 0 H .
Set (adjust) the desired item with the
cursor button 2 or 3.
• To adjust multiple items, repeat steps 4 and 5.
Adjustment item Button
Sets whether to clear the menu display
automatically a fixed time later or not.
(Factory setting : NO)
MENU AUTO YES: Clears the display automatically in
2/3
OFF
NO : Does not clear the display
NO
Sets whether to show the line display (Y/C,
VIDEO, etc.) at the top of the projected
screen or not. (Factory setting : ON)
OFF: Does not show the line display.
2/3
LINE DISPLAY
ON : Shows the line display.
OFF
Reverses video image right-to-left.
(Factory setting : OFF)
RIGHT LEFT
2/3
OFF: For the front method
REV.
ON : For upside hanging from the ceiling
OFF
Inverses video image upside-down.
(Factory setting : OFF)
TOP BOTTOM 2/3
OFF: For normal set-up
INV.
ON : For upside hanging from the ceiling
OFF
Sets the clamp pulse's position at the back
porch (BP) or on the sink tip (ST).
Normally, the clamp is used at BP. If, with
some PCs or workstations, the screen
becomes unstable such as being too dark
or too bright, try to switch to ST.
2/3
CLAMP
(factory setting: BP)
BP : The clamp pulse is positioned at the
ST : The clamp pulse is positioned on the
BP
When the number of pixels (resolution)
sought by the input video is smaller than
that (resolution) of D-ILA device, the video
image is then enlarged to virtually full
screen size of D-ILA device and projected
(resizing display). (Factory setting : ON)
Does not work (cannot be set) for video
system input.
OFF : Does not enlarge the video image for
2/3
RESIZE
ON : Enlarges virtually to the full screen
OFF
Adjustment content
about 25 seconds.
automatically.
YES
(The line display disappears about 5
seconds after it is shown.)
ON
ON
ON
back porch.
sink tip.
ST
projection. When the number of
pixels sought by video image is
smaller than that of D-ILA device,
projection takes place on a small
screen size with a black area around
the screen.
size of D-ILA device for projection
(resizing display).
ON
(To be continued on the next page)
45