Description, Specifications And Instructions; Description Of Symbols; Environmental Protection - Haussmann SMS15A-10-DB Manuel D'utilisation

DESCRIPTION, SPECIFICATIONS AND INSTRUCTIONS

Description of symbols

The rating plate on your tool may show symbols.
These represent important information about
the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Tool is listed by Underwriters Labo-
U L
C US
®
ratories and listed to Canadian Stan-
dards by Underwriters Laboratories

Environmental protection

Recycle unwanted materials instead
of disposing of them as waste. All
tools, hoses and packaging should be
sorted, taken to the local recycling centre and
disposed of in an environmentally safe way.
SMS 15A-10'-DB
Voltage
Input power
No load speed
Rated power
Blade size
Number of teeth
Max cutting depth (90°)
Max cutting depth (45°)
13 3/8x3 5/32" (34x8 cm)
0° Mitre / 0° Bevel
9 7/16x3 5/32" (24x8 cm)
45° Mitre / 0° Bevel
13 3/8x1 9/16" (34x4 cm)
0° Mitre / 45° Bevel
9 7/16x1 9/16" (24x4 cm)
45° Mitre / 45° Bevel
45°R Mitre / 45°R Bevel 9 7/16x1 3/32" (24x2.8 cm)
SMS 15A-12'-DB
Voltage
Input power
No load speed
Rated power
Blade size
Number of teeth
Max cutting depth (90°)
Max cutting depth (45°)
13 3/8x3 17/32" (34x9 cm)
0° Mitre / 0° Bevel
45° Mitre / 0° Bevel
0° Mitre / 45° Bevel
45° Mitre / 45° Bevel
45°R Mitre / 45°R Bevel
Safety instructions
Safety rules for laser lights
WARNING.Do not stare directly at the laser beam.
WARNING. It may be more difficult to see the
laser line in conditions of bright sunshine and on
certain surfaces
A hazard may exist if you deliberately stare into
120V ~ 60Hz the beam, please observe all safety rules as
follows;
15 Amp
• The laser shall be used and maintained in ac-
4500 RPM
cordance with the manufacturer's instructions.
1800 W
• Never aim the beam at any person or an object
Ø10" x Ø5/8"
other than the workpiece.
24
3 5/32" (8 cm)
• The laser beam shall not be deliberately aimed
at personnel and shall be prevented from
1 3/4" (4.5 cm)
being directed towards the eye of a person for
longer than 0.25s.
• Always ensure the laser beam is aimed at a
sturdy workpiece without reflective surfaces.
I.e. wood or rough coated surfaces are accep-
table. Bright reflective sheet steel or the like
is not suitable for laser use as the reflective
surface could direct the beam back at the
120V ~ 60Hz
operator.
15 Amp
• Do not change the laser light assembly with a
4500 RPM
different type. Repairs must be carried out by
1800 W
the laser manufacturer or an authorized agent.
Ø12" x Ø1"
CAUTION. Use of controls or adjustments or
40
performance of procedures other than those
3 15/16" (10 cm)
specified herein may result in hazardous radiati-
2 23/64" (6.4 cm)
on exposure.
9 7/16x3 17/32" (24x9 cm)
13 3/8x2 5/32" (34x5.5 cm)
9 7/16x2 5/32" (24x5.5cm)
9 7/16x1 1/2" (24x3.8 cm)
21
EN