Elco Klockner EK01B.4 L Notice D'emploi page 33

Summary
Contents
Summary
Function
Assembly
Start up
Service
Important notes
The EK01B...L-(H) light oil burner is
designed to run on extra-light heating oil.
The burner conforms to EN 267 in
terms of both design and function.
Assembly, startup and maintenance
must only be carried out by authorised
service technicians, observing current
guidelines, directives and
specifications.
Description of burner
The EK01B...L-(H) fuel oil burner is a
single-stage burner with fully-automatic
functioning and integral configuration.
Its performance range makes it suitable
for use with EN 303-compliant heat
generators, or with warm-air heating
systems conforming with DIN 4794,
DIN 30697 or EN 621.
Scope of delivery
The following items are supplied along
with the burner:
2 Oil hoses
1 Connection securing flange with
heat-insulating gasket
1 Bag containing attachment fittings
1 Plastic envelope containing
technical documentation
1 additional blast tube for burner
head
Contents . . . . . . . . . . . . . . . . . . . . . . 33
Important notes . . . . . . . . . . . . . . . . . . 33
Technical data, working area . . . . . . . . . . . 34
Dimensions, burner description . . . . . . . . . . 35
Pre-heating, operating and safety functions . . . . 36
Control and safety unit . . . . . . . . . . . . . . 37
Burner assembly . . . . . . . . . . . . . . . . . 38
Electrical connection, oil supply, oil burner pump . 38
Pre-startup check . . . . . . . . . . . . . . . . . 38
Adjustment settings, air flow control . . . . . . . . 39
Fuel oil pressure control, checking for
correct functioning . . . . . . . . . . . . . . . . . 40
Maintenance . . . . . . . . . . . . . . . . . . . . 41
Troubleshooting . . . . . . . . . . . . . . . . . . 42
The following standards must be
observed in order to ensure the safe,
environment-friendly and energy-saving
operation:
DIN 4755
Oil-fired devices in heating systems
EN 226
Connection of forced-draught atomising
oil and gas burners to heat generators
EN 60335-2
Safety of electrical equipment for
domestic use and similar purposes
Installation place
The burner must not be used in any
area containing corrosive fumes (e.g.
hairspray, tetrachloroethylene, carbon
tetrachloride); large amounts of dust or
a high level of air humidity (e.g. in
laundry rooms). Ensure that the site is
equipped with a ventilation inlet of at
2
least 150cm . Rules may vary
according to local legislation.
0301 / 13 010 881C
Page Declaration of conformity
for fuel oil burners
We, CEB
F-74106 ANNEMASSE Cedex, France
declare under our sole responsibility
that the following products:
EK01B.4 L-H
EK01B.4 L
EK01B.6 L
EK01B.9 L
comply with the following standards:
EN 50165
EN 55014
EN 60335
EN 60555-2
EN 60555-3
EN 267
Within the terms of following directives:
89 / 392/EEC Machine directive
89 / 336/EEC EMC directive
73 / 23 /EEC Low-voltage
92 / 42 /EEC
These products bear CE-marking
Annemasse, 1st April 2002
J.HAEP
We will accept no guarantee for
damage caused or injury sustained
due to any of the following causes:
Unauthorised use
–
Incorrect assembly or startup on the
–
part of either the purchaser or a third
party. This includes the fitting of
non-genuine parts.
Handover and operating instructions
The installer of the firing system must
provide the user with instructions on the
operation and maintenance no later
than at the moment in which the unit is
handed over for use.
These instructions should be displayed
in a prominent location at the point of
installation of the heating unit, and
should include the address and
telephone number of the nearest
customer service centre.
Advice to the user
Have the unit professionally serviced at
least once a year. It is strongly
recommended to enter into a
maintenance contract in order to
ensure trouble-free running.
device directive
Operating
efficiency directive
EN
33