O Vercurrent P Rotection - Daikin DX17VSS Serie Instructions D'installation

notice
• n -
ever InStall a phaSe advancIng capacItor
equIpped WIth an Inverter
tor WIll not only deterIorate poWer factor Improvement ef
,
fect But alSo may cauSe capacItor aBnormal heatIng accIdent
-
due to hIgh frequency WaveS
• d
o not change the SettIng of the protectIon devIceS
,
preSSure SWItch thermal SWItch
IS Shorted and operated forcIBly
d
SpecIfIed By aIkIn are uSed
• d
o not connect the ground WIre to SuctIon lIne
,
lIghtnIng rodS or telephone ground WIreS
The air conditioner rating plate lists pertinent electrical data
necessary for proper electrical service and overcurrent protec-
tion. Wires should be sized to limit voltage drop to 2% (max.)
from the main breaker or fuse panel to the air conditioner.
Consult the NEC, CEC, and all local codes to determine the
correct wire gauge and length.
Local codes often require a disconnect switch located near
the unit; do not install the switch on the unit.
o p
vercurrent rotectIon
The inverter control system software provides sufficient time
delay to protect from overcurrent conditions and permit the
compressor and fan motors to adjust their rotational speed.
h v c
Igh oltage onnectIonS
Route power supply and ground wires through the high volt-
age port and terminate in accordance with the wiring diagram.
. a
S thIS unIt IS
, -
InStallIng a phaSe advancIng capacI
.
. I
,
or other protectIon devIce
,
or partS other than thoSe
,
fIre or exploSIon could reSult
,
SeWage pIpeS
.
-
• B
efore connectIng the WIrIng to the termInal Block
-
the ShIeldIng plate
• p
recautIonS to Be taken for poWer Supply WIrIng
W
hen uSIng Stranded WIreS
f the
Style termInal for connectIon to the poWer Supply termInal
.
Block
p
lace the round crImp
.
covered part and Secure In place
,
Round crimp-style
terminal
Cup washer
Screw
Notch side
• W
hen connectIng the connectIon WIreS to the termInal Block
uSIng a SIngle core WIre
I
mproper Work may cauSe heat and fIreS
Strip wire end
to this point.
• u
Se the folloWIng method When InStallIng a SIngle core WIre
Screw
• Make sure to apply the rated voltage of 208/230V for the
unit.
• A power circuit (see the following table) must be provided
for connection of the unit. This circuit must be protected
with the required safety devices.
• When using residual current operated circuit breakers, be
sure to use a high-speed type (0.1 seconds or less) 200
mA rated residual operating current.
• Use copper conductors only.
• Use insulated wire for the power cord.
• Select the power supply cable type and size in accor-
dance with relevant local and national regulations.
10
cAUtion
. a
nd take It Back after WorkIng
,
make Sure to uSe a round crImp
-
Style termInalS on the WIreS up to the
.
A
Round Good
crimp-style
terminal
Wrong
Arrow view A
,
Be Sure to curl the end of the lead
.
Good
Excessive strip length
may cause electric shock
or current leakage.
Good
Cup
washer
A single core wire
A single core wire
B
Arrow view B
,
remove
.
.
-
Stranded wire
Screw
Round crimp-
style terminal
Cup washer
Screw
Cup washer
Round crimp-
style terminal
.
Wrong
Wrong
.