Filtration Cycle And Ozonisation Of The Water; Water Heating Cycle; Temperature Range; Ready/Rest Mode - HOESCH NEVADA Instructions De Montage Et D'utilisation

Michigan, Ontario, Winnipeg
TEMP+/TEMP- Setting the
temperature. Underneath this button is an LED
light, which indicates when the electric heater
is working. The water temperature is set and
controlled using the TEMP+/TEMP- button. The
current water temperature is only indicated once
the water pump has been running for about two
minutes. Pressing the TEMP+ or TEMP- button
takes you into the mode for setting the water
temperature. You can change the temperature by
pressing the button again. When the display stops
fl ashing after about three seconds, the required
temperature has been set.
LIGHT – Switching the underwater spotlights on
and off. The underwater spotlights are switched
on and off using the LIGHT button. The colour is
changed by pressing the ON-OFF button. The un-
derwater spotlights switch off automatically after
about four hours. Underneath this button is an LED
light, which indicates when the underwater spot-
lights are switched on.
JETS – Switching the water pump on and off.
Underneath this button is an LED light, which
indicates when the water pump is working.
Nevada
TEMP +/TEMP- Setting the required water tem-
perature. Underneath this button is an LED light,
which indicates when the electric heater is working.
The temperature is set using the TEMP button. The
current water temperature is only indicated once
the water pump has been running for about two
minutes. Pressing the TEMP- button takes you
into the mode for entering the water temperature.
Pressing it again changes the water temperature
setting in one direction. When the display stops
fl ashing after about three seconds, the required
temperature has been set. Pressing the button
again takes you back into the mode for setting
the water temperature. Pressing the button again
changes the water temperature in the opposite di-
rection.
AIR - Switching the blower on and off Underneath
this button is an LED light. which indicates when
the blower is working.
LIGHT – Switching the underwater spotlights on
and off. The underwater spotlights are switched
on and off using the LIGHT button. The colour
is changed by pressing the ON/OFF button. The
underwater spotlights switch off automatically af-
ter about four hours. Underneath this button is an
LED light, which indicates when the underwater
spotlights are switched on.
11
required water
Filtration occurs when the water is pushed through the
cartridge fi lter.
During fi ltration, the ozonator is also switched on.
The factory setting is for the fi ltration cycle to run once every 24
hours. It begins at 20.00 hrs and lasts for two hours according
to the time shown on the display. To improve the functionality
of the pool, the time displayed should be set as described in
Operating Instruction 133764 -Section 01.05. If necessary,
a second fi ltration cycle can be programmed (Operating
Instruction 133764 - Section 01.07).
The fi ltration is carried out with the help of a circulation pump.
12
To reach the required temperature, the water has to pass
through the electric heater. This fl ow is generated by the
water circulation pump.
13

Temperature range

The whirlpool allows you to set two separate temperature
ranges. The upper temperature is set using the "up" arrow
symbol. The lower temperature is set using the "down" ar-
row symbol.
These ranges can be set according to how frequently the
whirlpool is used. To set the temperature ranges, see Oper-
ating Instruction 133764 - Section 01.03.
14
In READY mode, the circulation pump comes on for at least
one minute every 30 minutes to check the current water
temperature. If the required temperature has not been
reached, the electric heater is switched on.
REST mode only allows the water to be heated during the
programmed fi ltration cycles.
Setting the fi ltration cycle (see Operating instruction 133764
- Section 01.04)
15
If the temperature sensors detect a dangerously low
temperature (below 7˚C), then the pumps (and in the case
of NEVADA pool the blower) is started automatically to
prevent water from freezing inside the elements.
JETS – Switching the water pump on and off. Un-
derneath this button is an LED light, which indi-
cates when the water pump is working.
Filtration cycle and ozonisation of the
water

Water heating cycle

READY/REST MODE

Protection at low temperatures

GB
31