Optional Accessories; Before Use; Handling Of The Packed Machine; Unpacking Of The Machine - ADIATEK sapphire 65 Emploi Et Entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

GB

OPTIONAL ACCESSORIES

Front light and relative switch.
3SD "SOLUTION SAVING SYSTEM DISPENSER".
Squeegee "V"-type.
Electric float switch.

BEFORE USE

HANDLING OF THE PACKED MACHINE

The machine is supplied with suitable packing fore-
seen for fork lift truck handling.
The total weight is 343kg.
Packing dimensions:
Base: 178 cm x 93 cm
Height: 138 cm
ATTENTION:
Do not place more than 2 packings on top of each
other.

UNPACKING OF THE MACHINE

1. Remove the external packing.
2. Unscrew the brackets (1+2) that secure the ma-
chine to the pallet.
3. Move the machine backwards, as indicated in the
figure, avoiding heavy contacts to mechanical parts.
4. Keep the pallet and the brackets for eventual
transport.

ACCESS TO THE BATTERY COMPARTMENT

1. Bring the machine on a levelled surface.
2. Rotate the seat platform forward up to the
blocking of the support.
3. Make sure that the recovery tank is empty, oth-
erwise proceed to its emptying (see under paragraph
"RECOVERY TANK EMPTYING AND CLEANING").
4. Rotate the recovery tank backwards until the
safety cables are put in tension.
5. Having finished any intervention, to close the
battery compartment, reposition first the recovery
tank, then, after having released the support, reposi-
tion the seat platform being careful that it is going
to block the tank engaging the slot placed on the
rear part of the tank to the seat.
21
BATTERY INSTALLATION AND SETTING OF THE
BATTERY TYPE
The machine is equipped either with batteries in se-
rial connection or elements of DIN-type assembled
together and connected in series for a total of 36
Volt, placed in its appropriate compartment under
the seat platform and must be handled using suita-
ble lifting equipment (due to weight, considering the
type of batteries chosen, and coupling system).
The batteries must be in accordance with CEI 21-5
Norms.
ATTENTION:
The machine and its battery check card foresee the
use of traditional lead or gel batteries.
CHECK THE CORRECT SETTING OF THE CHECK CARD
(see under paragraph "BATTERIES CHARGE LEVEL IN-
DICATOR" and "SETTING OF THE BATTERY CHECK
CARD").
ATTENTION:
Strictly follow manufacturer/distributor indications
for the maintenance and recharge of the batteries.
All installation and maintenance operations must be
executed by specialized staff, using suitable protec-
tion accessories.
For batteries installation it is necessary to reach the
battery compartment as indicated under paragraph
"ACCESS TO THE BATTERY COMPARTMENT".
1. Place the batteries in its compartment.
2. Connect the terminals, respecting the polari-
ties, avoiding contact with other parts that could
create short circuit.

ASSEMBLING OF THE ROLLBAR

For packing reasons the support of the blinking light
is supplied disassembled.
In each seat on the solution tank there are two
screws. On the lower screw there is fixed the safety
cable (1) to prevent the overturn of the recovery
tank when this is being opened.
Proceed as follows:
1. Take off the two screws (2) from the seats on the
tank.
2. Place the rollbar in its position so that the side
where the cable of the blinking light comes out cor-
responds to the side of the machine where there is
the connecting plug on the suction motor support of
the recovery tank.
3. Fasten the screws passing them in the same order
in their holes foreseen on the rollbar.
4. Complete the assembly connecting the connect-
ors (3) to supply the blinking light.
Afterwards, to remove the batteries from the ma-
chine, it is sufficient to take off only the upper
screws (where the cable is not fixed) from their seats
and rotate the rollbar backwards.
GB

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Sapphire 85

Table des Matières