Selecting The Direction Of Rotation - Black & Decker BDK700 Mode D'emploi

Electrical safety
#
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip counterclockwise until you can slide the side
u
handle (7) onto the front of the tool.
Rotate the side handle into the desired position.
u
Insert the depth stop (6) into the mounting hole as shown.
u
Set the drilling depth as described below.
u
Tighten the side handle by turning the grip clockwise.
u
Setting the drilling depth (fig. A)
Slacken the side handle (7) by turning the grip counter-
u
clockwise.
Set the depth stop (6) to the desired position. The maxi-
u
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
u
Fitting an accessory (fig. B & C)
Keyless chuck with spindle lock (Where supplied)
(fig. B)
Open the chuck by turning the sleeve (9) counterclockwise
u
Insert the bit shaft (10) into the chuck.
Tighten the chuck by turning the sleeve clockwise.
u
Keyed chuck (Where supplied) (fig. C
Open the chuck by turning the sleeve (11) counterclock-
u
wise.
(Original instructions)
Insert the bit shaft (10) into the chuck.u Insert the chuck
u
key (12) into each hole (13) in the side of the chuck and
turn clockwise until tight.
Removing and refitting the chuck (fig. D)
Open the chuck as far as possible.
u
Remove the chuck retaining screw, located in the chuck,
u
by turning it clockwise using a screwdriver.
Tighten an Allen key into the chuck and strike it with a
u
hammer as shown.
Remove the Allen key.
u
Remove the chuck by turning it counterclockwise.
u
To refit the chuck, screw it onto the spindle and secure it
u
with the chuck retaining screw.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the drilling mode
For hammer drilling in masonry and concrete, set the
u
operating mode selector (4) to the
For drilling in steel, wood and plastics, set the operating
u
mode selector (4) to the

Selecting the direction of rotation

For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(3) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
To switch the tool on, press the variable speed switch (1).
u
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch. This option does not
work in reverse rotation.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
ENGLISH
qr
position.
r
position.
5