Gear On/Off Lever (14; 15); Seat Adjustment (20); Engine Bonnet; Quick Release Supports (16:C) - Stiga Park 4WD Serie Manuel D'utilisation

Masquer les pouces Voir aussi pour Park 4WD Serie:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

(Translation of the original instructions)

6.12 GEAR ON/OFF LEVER (14; 15)

Lever that excludes variable gears.
The 2WD is equipped with a lever
4WD has two levers connected
to the rear axle (15:A) and to the
front axle (15:B).
The on/off lever must never be between
the external and internal position. This
condition overheats and damages the
transmission.
The levers allow you to move the machine man-
ually (by pushing or pulling), without starting the
engine.
The two positions are:
Drive on (14:A1; 15:A1-B1) - transmission en-
gaged for normal use.
Drive off (14:A2; 15:A2-B2) - transmission off.
The machine can be moved by hand.
Avoid towing the machine over long distances
or at high speeds. The transmission could be
damaged.
Do not operate the machine with the
drive off (lever in). There is a risk of
damage and oil leakage in the front
axle.

6.13 SEAT ADJUSTMENT (20)

The seat is reclining and can be adjusted
forwards and backwards as follows:
1. Loosen the knobs (20:A) without using tools.
2. Move the seat to the desired position.
3. Tighten the knobs (20:A) by hand.
The knobs (20:A) and the seat (20:B)
are damaged if tools are used.
The seat is equipped with a safety switch con-
nected to the safety system of the machine.
This means that when there is no one in the seat,
the machine cannot be started. (see 7.5).

6.14 ENGINE BONNET

For how to access the fuel cock, the
battery and the engine, see 5.2.
connected to the rear axle.
See (14:A).
ENGLISH

6.15 QUICK RELEASE SUPPORTS (16:C)

These supports allow you to easily and
The quick release supports allow you to easily
move the cutting device between two positions,
namely:
• Normal position, with the belt fully taut.
• Position 4 cm back from normal, with the belt
slack, so that the cutting device comes closest
to the base machine.
Since the tensioner is freed from the belt, the
quick release supports make it easy to replace
the belt and the cutting device assembly, also
making it easier to switch to the washing and
working positions.
Belt tension release (16; 18)
See also the instructions supplied with
the attachment and with the quick re-
lease support.
1. Remove the split pins or locking pins (16:B)
from both sides.
2. Open the quick release supports by pressing
on the rear sections with your heel (16:A).
Once the quick release supports are
open, the attachment arms are free,
therefore no longer firmly fixed to the
hook.
For any adjustment or maintenance
work, replace the arms on the support
and close it again
1. Perform the necessary task, such as:
• Unhook the belt.
• Replace the attachment by releasing the arms
(18).
Belt tensioning (16; 17)
Tension one side first, then the other following the
instructions below.
Do not turn the lever with your hands.
There is a risk of crushing injuries.
1. Place a foot on the lever (17:A) and carefully
rotate it half a turn forward.
2. Install the split pins or locking pins (16:B).
3. Repeat the operation on the other side.
quickly switch from one accessory
to another.
EN
15

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Park 2wd seriePark 320 pPark 320 pwPark 340 pwxPark 345 pwxP 901 c ... Afficher tout

Table des Matières