Important - Worx WG324E Notice Originale

ASSEMBLING THE EXTENSION POLE TO THE MACHINE
(See Fig F3, F4)
Step 1: Align and insert the extension pole into the saw.
Step 2: Hang the buckle on the hook of the saw. Press
the Clamping Lever to tighten the extension pole to the
machine.
NOTE: Make sure the extension pole is locked into
position securely before operation.
REMOVING THE EXTENSION POLE (See Fig. F5)
Loosen the Clamping Lever to release the buckle. Press
the Extension Pole Release Button to disconnect the
extension pole with the saw.
WARNING! When using this machine with the
Extension Pole, make sure that the battery pack has
been removed.
LUBRICATION
NOTE: Chain life and cutting capacity depend on
optimum lubrication. Therefore, the chain should
be oiled before operation.
IMPORTANT: It is important to use bar and chain
lubricant that is formulated to perform over a
wide temperature range with no dilution required.
This can be found at the location where you
purchased this saw or your local hardware store. Do
not use dirty, used or otherwise contaminated
oil. Damage may occur to the bar or chain. Use of
non-approved oil will void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
away from heat or open flame.
1. Switch off the pruning saw and remove the battery.
2. Place the pruning saw on a level surface with the
Housing-Cover facing up.
3. Clean the Guide Bar and Chain with a soft brush or
solvent.
4. Apply lubrication oil in area (a) between Guide Bar
and Chain. (See Fig. G)
5. Fit the battery. Switch on the pruning saw.
Lubricationl oil is evenly distributed over the chain. The
saw chain is lubricated.
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are specially
designed to work together so do not attempt to use
any other devices. Never insert or allow metallic objects
into your charger or battery pack connections because of
an electrical failure and hazard will occur.
NOTE: Your battery pack is UNCHARGED and you must
charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
(1) CHARGING YOUR BATTERY PACK (See Fig. H1, H2)
The Li-ion battery is protected against deep discharging.
When the battery is empty, the machine is switched off
Cordless Pruning Saw
by means of a protective circuit.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow time
for the battery to cool down before recharging.
(2) TO REMOVE OR INSTALL BATTERY PACK (See Fig. I)
Depress the Battery Pack Release Button to remove the
Battery Pack from your tool. After recharging, insert the
Battery Pack into the battery port. A simple push and
slight pressure will be sufficient until a click is heard.
Check to see if the battery is fully secured.
NOTE: When removing the battery pack, hold it
firmly to avoid dropping and injury.
(3) HOLDING AND CONTROLLING THE PRUNING SAW
(See Fig. J)
Hold and control the pruning saw with one hand on the
Grip Area – wrap your thumb around the Grip Area.
Hold and control the pruning saw with your other hand
on the Secondary Grip Area.
2. SWITCHING ON AND OFF (See Fig. K)
ATTENTION: Check the battery pack before using
your cordless tool. Only use the battery pack
listed in the accessories section.
For switching on the tool, press the Lock-Out Button,
then fully press the On/Off Switch and hold in this
position. The Lock-Out Button can now be released.
For switching off, release the On/Off Switch.
3. CUTTING
IMPORTANT: Check recent replaced chain tension
about every 10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying on the
ground. This will keep the chain from touching the
ground as it cuts through the log.
Touching the ground while the Chain is moving is
dangerous and will dull the Chain.
(3) When ready to make a cut, push the Lock-Out Button
completely in with the right thumb and squeeze the
trigger. This will turn saw on. Releasing the trigger
will turn the saw off. Make sure the saw is running at
full speed before starting a cut.
(4) When starting a cut, slowly place moving chain
against the wood. The wood should be as close to
the saw body as possible. Hold saw firmly in place
to avoid possible bouncing or skating (sideways
movement) of saw.
(5) Guide the saw using light pressure and do not put
excessive force on the saw, letting the saw do its
work. The motor will overload and can burn out. It will
do the job better and safer at the rate for which it was
intended.
(6) Remove the saw from a cut with the saw running
at full speed. Stop the saw by releasing the On/off
Switch. Make sure the chain has stopped before
setting the saw down.
(7) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a fluid motion
and a steady cutting rate.
17
EN