Wet Vacuuming - Metabo ASR 36-18 BL 25 M SC Notice Originale

8.2

Wet vacuuming

Never operate the machine without inserting a
filter cassette (22) first. The machine may be
destroyed and water may also escape.
You can use PE disposal bags (11). The filter
cartridges (22) are suitable for wet vacuuming.
Before carrying out any wet vacuuming, remove the
dry vacuumed material. This process will prevent
severe soiling and encrustation.
The integrated water sensor switches off the motor
when the container is full. Empty the device. If the
device is not switched off, the restart protection
device remains effective. The device is not
operable again until it has been switched off and
switched back on again.
After switching off, some water may run back out of
the hose.
Before emptying, first of all take the suction hose out
of the liquid.
If you are then going to dry vacuum, insert a dry filter
cassette. (If you are frequently switching between
dry and wet vacuuming, we recommend the use of
a second set of filter cassettes.) Allow the filter
cassettes, container and accessories to dry:
otherwise dust may adhere to damp components.
8.3 Use as industrial vacuum cleaner (IS):
Turn main switch (1) to the RIGHT (position "MAN").
Adjust the rotary switch (5) to the hose diameter of
the suction hose fitted.
If the volume flow falls below the set value, the
volume flow control display (6) lights up to signal
that the container must be emptied, or that the
fleece filter bag (12) or the PE disposal bag (11)
must be changed or the filter must be cleaned.
8.4 Use as a dust extractor (ENT):
The dust extractor must not be connected to more
than one dust source.
Turn the main switch (1) and vibrator switch (2) to
"AUTO" position.
Adjust the rotary switch (5) to the hose diameter of
the suction hose fitted. For more detailed
information, see section 7.4.
8.5 Transport
Close the suction opening (17) with sealing plugs
(18). Join the hose ends to prevent dust from
escaping.
Wrap the suction hose about the vacuum cleaner.
Place the accessories in a suitable plastic bag and
seal the bag.
The upper part (14) must be securely sealed to the
container (16) - check that the snap locks (15) are
closed.
9. Cleaning
9.1 General Cleaning Instructions
Clean the container and accessories with water.
Wipe the upper part (14) with a damp cloth.
Caution! This device contains dust that is harmful to
health. Discharge and maintenance operations
(including disposal of the dust collection containers)
must only be carried out by qualified specialists
wearing appropriate protective clothing and
equipment.
Emptying the Container
Only permitted for dusts with
occupational exposure limits > 1mg/m
- Remove the battery packs .
- Remove the suction hose, close the suction
opening (17) with the sealing plug (18).
- Open the snap locks (15). Remove the upper part
(14) of the device from the container (16).
Disposing of the Fleece Filter Bag
- Remove the battery packs .
- Put on a dust mask.
- Remove the suction hose, close the suction
opening (17) with the sealing plug (18).
- Open the snap locks (15). Remove the upper part
(14) of the device from the container (16).
- Carefully pull back the fleece filter bag (12) from
the suction opening (18) . Seal the flange of the
fleece filter bag by folding over the cover.
- Dispose of the vacuumed material in accordance
with legal regulations.
Disposal of a PE Disposal Bag
- Switch on the vacuum cleaner and shake the filter
cassettes: Turn vibrator switch (2) to the RIGHT in
"MAN" position and release again. The vibrator
cleans the filter cassettes (22) for about 10 sec.
- Switch off the vacuum cleaner: turn the switch (1)
to the "OFF" position.
- Put on a dust mask.
- Remove the suction hose, close the suction
opening (17) with the sealing plug (18).
- Open the snap locks (15). Remove the upper part
(14) of the device from the container (16). Before
setting down the upper part, turn switch (1) to the
"ON/MAX" position so that any falling dust is
vacuumed.
- Carefully pull back the PE disposal bag (11) from
the suction opening (17). Seal the flange of the PE
disposal bag by folding over the cover.
- Dispose of the vacuumed material in accordance
with legal regulations.
9.2 Safety instructions for mitre saws
In the case of class M machines, the outside of the
machine should be cleaned (vacuumed and wiped
down), or treated with sealants before being
removed from the hazardous area. All machine
parts must be considered to be contaminated when
removed from the hazardous area: suitable
measures must be taken to prevent any dispersal of
the dust. When carrying out maintenance or repairs,
it is essential to dispose of any contaminated
objects that cannot be adequately cleaned. These
objects must be disposed of using impermeable
ENGLISH en
3
.
19