Initial Operation; Battery Pack - Metabo ASR 36-18 BL 25 M SC Notice Originale

1 Main switch
2 Vibrator switch
3 Capacity and signal indicator
4 Capacity indicator button
5 Rotary switch for selecting the extraction hose
diameter
6 Volume flow control display
7 Battery pack release button*
8 Battery pack(s) *
9 Protective cover (battery packs)
10 Lock (to lock the protective cover)
11 PE disposal bag *
12 Fleece filter bag*
13 Hose hooks
14 Upper part
15 Snap lock
16 Bottom part
17 Suction opening
18 Sealing plug
19 Locking knob
20 Locking bar (for opening the hood to change
filter cassettes)
21 Motor protection filter
22 Filter cassette (according to IFA C)
* depending on equipment/not included in scope of
delivery

6. Initial Operation

6.1 Inserting a Fleece Filter Bag
We recommend using fleece filter bags for:
- Applications, where small amounts of fine dust are
created (e.g. spot-grinding and grinding of paint
and lacquer coatings, extraction of drilling
applications with small diameters < 10 mm of
short duration, etc.).
- Use of machines, such as: routers, planers, small
grinding machines, etc.
Switch off device on the mains switch (1), remove
battery packs (8), open snap locks (15) . Remove
the upper part (14) of the device from the container
(16).
Turn the red rotary switch (on
the inside of the suction
opening) until the stop: the text
"CLOSE" shows upwards to
the marking ▲.
Hold a new fleece filter bag on the flange and, with
its opening, guide it first over the latch at the bottom
part of the suction opening, then fit up to the stop on
the suction opening. Replace the upper part (14) on
the container (16) and close the snap locks (15).
6.2 Inserting a PE Disposal Bag
PE filter bags (11) are suitable for both wet and dry
vacuuming.
We recommend the use of PE-disposal bags for:
- Applications, where larger amounts of dust are
created (e.g. removal of plaster surfaces, spot-
grinding and grinding of screeds, etc.).
- Use of machines, such as e.g.: renovation milling
machines, renovation grinders, drywall grinders,
wall grinders etc.
Turn the vibrator switch (2) to the LEFT in "AUTO"
position.
Switch off device, remove battery packs (8), open
snap locks (15) . Remove the upper part (14) of the
device from the container (16).
Turn the red rotary switch (on
the inside o the suction
opening) to the stop: the text
"OPEN" shows upwards to the
marking ▲.
Hold the PE disposal bag (11) on the flange and,
with its opening, guide it first over the latch at the
bottom part of the suction opening, then fit up to the
stop on the suction opening.
Spread out the PE disposal bag (11) evenly across
the container floor. Arrange the edges of the PE
disposal bag around the container rim so that the
bag is firmly clamped on all sides by the upper part
(14) once replaced.
Replace the upper part (14) on the container (16)
and close the snap locks (15).
6.3

Battery pack

Charge the battery packs before use.
Recharge the battery packs if performance
diminishes.
Instructions on charging the battery packs can be
found in the operating instructions of the Metabo
charger.
In case of Li-Ion battery packs with capacity and
signal display (3) (equipment-specific):
- Press the button (4), the LEDs indicate the charge
level.
- The battery pack(s) is(are) almost flat and must be
recharged if one LED is flashing.
Inserting and removing the battery pack
Use either one 36 V battery pack or two 18 V battery
packs.
- recommended capacity 8.0 and greater. The use
of battery packs with a smaller capacity (Ah)
reduces the service life but not the suction power.
- We recommend the use of battery packs with
identical item number.
- The use of battery packs with different capacity
(Ah) is permitted. In this case, the battery pack with
the smaller capacity (Ah) determines the useful life.
Insertion: Push the lock (10) downwards and fold
down the protective cover (9) . Slide in the battery
pack(s) (8) until it engages. Close the protective
cover (9) .
Removal: Push the lock downwards (10) and fold
the protective cover (9) downwards. Press the
ENGLISH en
17