Table des Matières
Publicité
Assembly Instructions
GB
Incorrect or excessive exercise may damage your health.
Any interference with parts of the product that are not described
within the manual may cause damage, or endanger the person
using this machine. Extensive repairs must only be carried out
by KETTLER service staff or qualified personnel trained by KET-
TLER.
To ensure that the safety level is kept to the highest possible
standard, determined by its construction, this product should be
Handling the equipment
Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
Do not set the equipment up in rooms which are frequently used
or close to doors, entries etc.
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
The rowing machine must be set up on an even impact-resistant
base. To absorb the vibrations, lay a straw or rubber mat under
the machine.
The product is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the man-
ufacturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
A few drops of viscous oil should be applied to the bearing
Instructions for Assembly
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
Please note that there is always a danger of injury when work-
ing with tools or doing manual work. Therefore please be care-
ful when assembling this machine.
Ensure that your working area is free of possible sources of dan-
ger, for example don't leave any tools lying around. Always dis-
pose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children
play with plastic bags!
List of spare parts page 20-23
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see handling).
Example order: Art. no. 07977-900 / spare-part no. 70132105
/ 2 pieces / S/N ....................
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in (in-
ternal) packaging, which is safe for transportation, in the original
box if possible.
4
serviced regularly (once a year) by specialist retailers.
In choosing the location of the apparatus, ensure a sufficient sa-
fety distance from any obstacles. The apparatus must not be
mounted in the immediate vicinity of main passageways (paths,
doorways, corridors).
Nobody may be in the moving range of a training person du-
ring training.
sleeves of the hydraulic absorbers and the rowing levers. Care
should be taken that the oil does not drip onto the floor!
After a longer period of disuse, the hydraulic absorbers may not
achieve their best performance at once. Before beginning exer-
cising or after a period of disuse, it is recommended to activate
the absorbers by several pumping movements.
Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment.
To operate correctly, the pulse function requires a minimum volt-
age of 2,7 volts.
Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.
Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
When training intensivly shock absorbers may become very hot.
Please avoid contact and do not touch the shock absorbers af-
ter training.
The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
structed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand un-
til resistance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
It is important to provide a detailed defect description / damage
report!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material".
Waste Disposal
KETTLER products are recyclable. At the end of its useful life plea-
se dispose of this article correctly and safely (local refuse sites).
Publicité
Table des Matières
