Samsung RF23HSESBSR Guide D'utilisation page 23

( 3 ) Quick Sparkling (Fill up (3 sec))
The Quick Sparkling button serves two
purposes:
- To produce sparkling water rapidly.
- To active the Fill Up function.
1) Quick Sparkling Function
When you touch the Quick Sparkling button,
the ( ) icon lights and the refrigerator makes
sparkling water rapidly at the level indicated by
the Sparkling Level icon.
If there is no sparkling water in the Sparkling
Water tank, the refrigerator will begin making
sparkling water immediately.
If there is sparkling water in the tank, the
refrigerator applies the Quick Sparkling function
the next time it makes sparkling water.
2) Fill Up Function
When you replace the SodaStream carbonator,
press the 'Quick Sparkling/Fill up (3 sec)' button
for 3 seconds to active the Fill Up function.
The refrigerator will fill the sparkling water tank
with water and inject CO
make sparkling water.
The sparkling level of the water may differ
from the set level, depending on the amount
and CO concentration of the sparkling water
2
remaining in the tank.
If the tank is empty or the concentration is very
low, the refrigerator will make sparkling water at
the level Indicated by the Sparkling Level icon.
If the sparkling level is not what you expected,
select the desired sparkling water carbonation
level (see page 24).
The next time the refrigerator makes sparkling
water, it will make it at the level you selected.
( 4 ) Fridge (Power Cool (3 sec))
The Fridge button serves two purposes:
- To set the Fridge to your desired
temperature.
- To turn the Power Cool function on and off.
1) To set the Fridge temperature, press the
Fridge button repeatedly.
Each time you press the button, you change
the temperature setting.
You can set the temperature between 44 °F
(7 °C) and 34 °F (1 °C).
2) Power Cool function
Touch and hold this button for 3 seconds to
decrease the time needed to cool products in
the Refrigerator.
It can be helpful if you need to quickly cool
easily spoiled items or if the temperature in the
fridge has warmed dramatically (For example, if
the door was left open).
( 5 )
gas into the water to
2
( 6 )
English - 23
Lighting (ºC ↔ ºF (3 sec))
Lighting button serves two purposes:
- To turn the dispenser light on and off
- To switch the temperature units between ºC
and ºF
1) Light Function
Touching the Lighting button turns on the
Dispenser LED lamp in continuous mode so
that it stays on continuously.
The button also lights up.
If you want the Dispenser lamp to come on only
when someone uses the dispenser, press the
Lighting button to turn the continuous mode off.
2) To switch the temperature units between
ºC and ºF Touch and hold this button for 3
seconds to select the temperature display
you want.
Each time you press and hold the button, the
ºC and ºF temperature modes alternate and
the ºC or ºF icon lights up, indicating your
selection.
Energy Saver (Control Lock (3 sec))
Energy Saver button serves two purposes:
- To turn the Energy Saver mode on and off
- To turn the Control Lock function on and off.
1) Energy Saver Function
When you turn Energy Saver on, the Energy
Saver icon lights.
Turn Energy Saver off and the icon goes off.
The Energy Saver function is set to ON in the
factory.
If condensation or water drops appear on the
doors, turn the Energy Saver mode off.
2) Control Lock Function
Touch and hold this button for 3 seconds to
lock the display, the Flex Zone panel, and the
dispenser buttons so the buttons can not be
used.
When Control Lock is on, the refrigerator does
not dispense ice, water, or sparkling water,
even if the Dispenser Lever is pressed.
The Control Lock icon lights up to indicate
you've activated the Control Lock function.
Press 3 seconds to unlock.